Home » Intel Manuals » Desktops » Intel SR1630BC » Manual Viewer

Intel SR1630BC Service Guide - Page 19

List of s

UPC - 735858208123

Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

List of Figures Figure 1. Intel® Server System SR 1630BC 3 Figure 2. Cable Routing Drawing 6 Figure 3. System Components 7 Figure 4. Server Board Connector and Component Locations 8 Figure 5. Configuration Jumper Location 10 Figure 6. Light Guided Diagnostic LEDs 12 Figure 7. Back Panel Connectors 13 Figure 8. Front Panel Control Panel - Intel® Server System SR1630BC 15 Figure 9. Server System I/O Connector Locations 17 Figure 10. Optional Peripherals 18 Figure 11. DIMM Configuration Diagram 20 Figure 12. Channel Slots Configuration 21 Figure 13. Removing the Front Bezel 24 Figure 14. Installing the Front Bezel 24 Figure 15. Removing the Server System Cover 25 Figure 16. Installing the Server System Cover 26 Figure 17. Removing the Processor Air Duct 27 Figure 18. Installing the Processor Air Duct 28 Figure 19. Installing the Memory 29 Figure 20. Lifting the Load Lever 31 Figure 21. Open the Load Plate 32 Figure 22. Remove the Socket Protective Cover 32 Figure 23. Remove the Processor Protective Cover 32 Figure 24. Installing the Processor 33 Figure 25. Close the Load Plate and Socket Lever 33 Figure 26. Protective Film Removal 34 Figure 27. IU Reference Heat sink Assembly 35 Figure 28. Locating Drive Positions 37 Figure 29. Removing Drive Carrier from Server System 38 Figure 30. Installing Drive into the Drive Carrier 38 Figure 31. Installing Drive Assembly into the Server System 39 Figure 32. Connecting Hard Drive Power and Data Cables 40 Figure 33. Removing Drive Carrier from the Server System 41 Figure 34. Removing the Knockout in Bezel for Optical Opening 42 Figure 35. Attaching the Brackets to the Optical Drive 43 Figure 36. Installing the Optical Drive into the Server System 43 Figure 37. Removing the Slimline Optical Drive Assembly from the Server System 44 Figure 38. Removing the Brackets from the Slimline Optical Drive Assembly 44 Figure 39. Removing the PCI Riser Assembly from the Server System 45 Figure 40. Installing the PCI Riser Assembly 46 Figure 41. Installing the PCI Riser Assembly from the Server System 47 Figure 42. Installing a PCI Card in a Riser Card 47 Intel® Server System SR1630BC Service Guide xix

Section	Page
Intel® Server System SR1630BC Service Guide	5
About this Manual	5
Manual Organization	5
Product Contents	6
Intel® Server System SR1630BC - Product Contents	6
Note: You may need or want to purchase one or more of the following items for your server:	6
Safety Information	9
Important Safety Instructions	9
Wichtige Sicherheitshinweise	9
Consignes de sécurité	9
Instrucciones de seguridad importantes	9
Warnings	11
Table of Contents	13
List of Figures	19
List of Tables	21
1 Server System References	23
2 Server System Features	25
Figure 1. Intel® Server System SR1630BC	25
Cable Routing	27
Figure 2. Cable Routing Drawing	28
Chassis Component Identification	29
Internal Components	29
A. Rack handles (two)	29
B. Processor air duct	29
C. System memory DIMM sockets	29
D. PCI add-in card bracket	29
E. Power supply	29
F. CPU Heatsink (two)	29
G. System blower fans (two)	29
H. Hard drives (two)	29
I. Control panel	29
J. Slimline optical drive	29
Figure 3. System Components	29
Server Board Connector and Component Locations	30
A. SATA 3	30
B. Internal dual port USB2.0 header	30
C. SATA 5	30
D. SATA 4	30
E. Slot 3, PCI Express* x4	30
F. Slot 4, 32-bit/33 MHz PCI	30
G. Intel® RMM3 slot	30
H. Slot 5, PCI Express* x8	30
I. Slot 6, PCI Express* x8 (Riser card)	30
J. Slot 7, PCI Express* x8	30
K. Black panel I / O ports	30
L. Diagnostic LEDs	30
M. Status LED	30
N. ID LED	30
O. External Serial B header	30
P. SATA Key	30
Q. System fan 3 header	30
R. Main power connector	30
S. DIMM sockets off Processor 1 socket (Channel A, B)	30
T. Power Supply Auxiliary Connector	30
U. SSI 24-pin Front Panel connector	30
V. System fan 2 header	30
W. CPU 1 fan header	30
X. CPU Power Connector	30
Y. CPU Socket 1	30
Z. Intel® 5500 Chipset	30
AA. CPU Socket 2	30
BB. CPU 2 fan header	30
CC. System fan 1 header	30
DD. DIMM sockets off Processor 2 socket (Channel D, E)	30
EE. SATA SGPIO	30
FF. SATA 0	30
GG. SATA 1	30
HH. SATA 2	30
Figure 4. Server Board Connector and Component Locations	30
Configuration Jumpers	31
Figure 5. Configuration Jumper Location	32
Intel® Light Guided Diagnostics	33
Figure 6. Light Guided Diagnostic LEDs	34
A. POST Code Diagnostic LEDs	34
B. Status LED	34
C. System ID LED	34
D. HDD LED	34
E. System Fan 3 Fault LED	34
F. 5 VSB LED	34
G. DIMM Fault LED	34
H. System Fan 2 Fault LED	34
I. CPU 1 Fan Fault LED	34
J. CPU 2 Fan Fault LED	34
K. System Fan 1 Fault LED	34
L. DIMM Fault LED	34
Back Panel Connectors	35
A. Serial Port A	35
B. Video	35
C. USB Port 6-7	35
D. USB Port 8-9	35
E. NIC Port 1	35
F. NIC Port 2	35
Figure 7. Back Panel Connectors	35
RAID Support	36
Note: For AHCI capability in EFI, the AHCI legacy Option ROM should be set to “disabled”.	36
Front of Server System	37
Standard Control Panel	37
A.	37
B.	37
C.	37
D.	37
E.	37
F.	37
G.	37
Figure 8. Front Control Panel - Intel® Server System SR1630BC	37
Bezels	38
Rear of Server System	39
A. AC Power Connector	39
B. Serial Port A	39
C. Video Connector	39
D. NIC 1 Connector (10 / 100 / 1000 Mb)	39
E. NIC 2 Connector (10 / 100 / 1000 Mb)	39
F. USB Ports 6 and 7	39
G. USB Ports 8 and 9	39
H. PCI Express* Slot	39
Figure 9. Server System I/O Connector Locations	39
Peripheral Devices	40
A. Slimline optical drive bay	40
B. Hard drive bay HDD0 (located under the slimline optical drive bay)	40
C. Hard drive bay HDD1	40
Figure 10. Optional Peripherals	40
Hard Disk Drives	40
Slimline Optical Drive Carrier	41
Rack-Mounted Systems	41
Hardware Requirements	41
Processor	41
Memory	42
Figure 11. DIMM Configuration Diagram	42
Figure 12. Channel Slots Configuration	43
Memory Sparing and Mirroring	43
Power Supply	44
Optional Hardware	44
Intel® RAID Activation Key	44
Hard Disk Drives	44
Note: The Intel® Remote Management Module 3 will not be supported in the Intel® Server System SR1630BC system.	44
3 Hardware Installations and Upgrades	45
Before You Begin	45
Note: Whenever you service the system, you must first power down the server and unplug all peripheral devices and the AC power cord.	45
Tools and Supplies Needed	45
System References	45
Removing and Installing the Front Bezel	45
Removing the Front Bezel	46
Figure 13. Removing the Front Bezel	46
Installing the Front Bezel	46
Figure 14. Installing the Front Bezel	46
Removing and Installing the System Cover	47
Removing the System Cover	47
Note: You may need a non-skid surface or a stop behind the server system to prevent the server system from sliding on your work surface.	47
1. Remove the top cover screw (see letter “A”).	47
2. Remove the two screws at the front of the chassis (see letter “A” in the following figure).	47
3. Loosen the screw at the rear of the chassis (see letter “B”).	47
4. Push rearward on the blue grip point at the front of the server.	47
5. Slide the cover back until it stops and then lift the cover upward to remove it. See letter “C”.	47
6. Slide the cover back until it stops and lift the cover upward to remove it (see letter “B”).	47
Figure 15. Removing the Server System Cover	47
Installing the System Cover	47
1. Observe the safety and ESD precautions at the beginning of this book. See “Safety Information” on page -ix.	47
2. Place the cover over the server system so that the side edges of the cover sit just inside the server system sidewalls. Slide the cover forward (see letter “A” in Figure 16).	48
3. Tighten the screw at the rear of the server (see letter “B”) and install the two screws at the front of the server (see letter “C”).	48
Figure 16. Installing the Server System Cover	48
Removing and Installing the Processor Air Duct	48
Removing the Processor Air Duct	48
1. Observe the safety and ESD precautions at the beginning of this book. See “Safety Information”.	48
2. Power down the server and unplug all peripheral devices and the AC power cable.	48
3. Remove the server system cover. For instructions, see “Removing the System Cover”.	48
4. Lift the processor air duct from its location behind the two system blower fans.	48
5. Lift the processor air duct from its location over the two processor sockets.	49
Figure 17. Removing the Processor Air Duct	49
Installing the Processor Air Duct	49
1. Observe the safety and ESD precautions at the beginning of this book. See “Safety Information”.	49
2. Power down the server and unplug all peripheral devices and the AC power cable.	49
3. Remove the server system cover. For instructions, see “Removing the System Cover”.	49
4. Lower the air duct into place; insert the two hooks at the front of the processor air duct into the corresponding slots on th...	49
Figure 18. Installing the Processor Air Duct	50
Installing and Removing Memory	50
Installing DIMMs	50
1. Observe the safety and ESD precautions at the beginning of this book.	50
2. Turn off all peripheral devices connected to the server.	50
3. Turn off the server.	50
4. Disconnect the AC power cord from the server.	50
5. Remove the cover from the server and locate the DIMM sockets (see “Installing the Memory”).	50
Figure 19. Installing the Memory	51
6. Make sure the clips at either end of the DIMM socket(s) are pushed outward to the open position (see letter “A” in Figure 19).	51
7. Holding the DIMM by the edges, remove it from its anti-static package.	51
8. Position the DIMM above the socket. Align the two small notches in the bottom edge of the DIMM with the keys in the socket (see letter “B” in Figure 19).	51
9. Insert the bottom edge of the DIMM into the socket (see letter “C” in Figure 19).	51
10. When the DIMM is inserted, push down on the top edge of the DIMM until the retaining clips snap into place (see letter “D” in Figure 19). Make sure the clips are firmly in place (see letter “E” in Figure 19).	51
11. Replace the server’s cover and reconnect the AC power cord.	51
Removing DIMMs	51
1. Observe the safety and ESD precautions at the beginning of this book.	51
2. Turn off all peripheral devices connected to the server. Turn off the server.	51
3. Remove the AC power cord from the server.	51
4. Remove the server's cover.	51
5. Gently spread the retaining clips at each end of the socket. The DIMM lifts from the socket.	51
6. Holding the DIMM by the edges, lift it from the socket, and store it in an anti-static package.	51
7. Reinstall and reconnect any parts you removed or disconnected to reach the DIMM sockets.	52
8. Replace the server's cover and reconnect the AC power cord.	52
Installing or Replacing the Processor	53
Note: Use the following instructions to install or replace a processor instead of using the instructions that came with the processor.	53
Caution: Processor must be appropriate: If you install a processor that is inappropriate for your server, you may damage the server board. See “Server System References” for a link to the list of compatible processor(s).	53
ESD and handling processors: Reduce the risk of electrostatic discharge (ESD) damage to the processor by doing the following: (1...	53
Installing the Processor	53
1. Observe the safety and ESD precautions at the beginning of this book. See “Safety Information” for more information.	53
2. Turn off all peripheral devices connected to the server and turn off the server.	53
3. Disconnect the AC power cord from the server.	53
4. Remove the server's cover. See the document that came with your server chassis for instructions on removing the server's cover.	53
5. Locate the processor socket and open the socket lever (see Figure 20).	53
Figure 20. Lifting the Load Lever	53
6. Open the load plate (see letter “A” in Figure 20 and letter “B” in Figure 21).	53
Figure 21. Open the Load Plate	54
7. Remove the socket protective cover (see Figure 22).	54
Figure 22. Remove the Socket Protective Cover	54
8. Take the processor out of the box and remove the protective shipping cover (Figure 23).	54
Figure 23. Remove the Processor Protective Cover	54
9. Align the processor cutouts to match the two socket pins, and then insert the processor into the socket as shown in Figure 24.	55
Figure 24. Installing the Processor	55
10. Close the load plate (see the letter “A” in Figure 25), close the socket lever and ensure the load plate tab engages under the socket lever when fully closed. (See letter “B” and “C” in Figure 25)	55
Figure 25. Close the Load Plate and Socket Lever	55
Note: Make sure the alignment triangle mark and the alignment triangle cutout align correctly. To assist in package orientation and alignment with the socket:	55
Installing the Heat Sink(s)	56
Figure 26. Protective Film Removal	56
1. If a protective film covers the thermal interface material (TIM) on the underside of the heat sink, remove the protective film.	56
2. Align heat sink fans to the front and back of the chassis for correct airflow. Airflow goes from front-to-back of chassis.	56
3. Each heat sink has four captive fasteners and should be tightened as shown.	56
4. Using a #2 Phillips* screwdriver, finger-tighten each fastener diagonally according to the white-circled numbers (see Figure 27).	56
5. Securely re-tighten each fastener again in the same order as performed in Step 4.	56
6. Attach fan power cable to server board as shown.	56
Figure 27. IU Reference Heat sink Assembly	57
7. Reinstall and reconnect any parts you removed or disconnected to reach the processor sockets.	57
8. Replace the server’s cover and reconnect the AC power cord. See the docmentation that came with your server chassis for instructions on installing the server’s cover.	57
Replacing a Processor	57
1. Observe the safety and ESD precautions at the beginning of this book.	57
2. Turn off all peripheral devices connected to the server. Turn off the server.	57
3. Remove the AC power cord from the server.	57
4. Remove the server's cover.	57
5. Unplug the processor fan cable from the server board.	57
6. Loosen the four captive screws on the corners of the heat sink.	57
7. Twist the heat sink slightly to break the seal between the heat sink and the processor.	57
8. Lift the heat sink from the processor. If it does not pull up easily, twist the heat sink again. Do not force the heat sink from the processor. Doing so could damage the processor.	57
9. Lift the processor lever.	57
10. Raise the CPU load plate.	57
11. Remove the processor.	58
12. If installing a replacement processor, see “Installing the Processor”. Otherwise, install the protective socket cover over the empty processor socket and reinstall the chassis cover.	58
Installing and Removing a Fixed Hard Drive	58
Caution: Fixed mount hard drives are NOT hot-swappable. Before removing or replacing the drive, you must first take the server o...	58
Installing and Removing a Hard Disk Drive	58
Caution: The hard drives are NOT hot swappable. Before removing or replacing a hard drive, you must first take the server out of...	58
You can install up to two SATA drives. The HDD0 drive bay is at the left side of the chassis, underneath the optional CD-ROM dri...	58
Note: The server system does not support all hard drives. See “Server System References” for a link to a list of supported hardware.	58
1. Locate the drive position you want to use.	58
Figure 28. Locating Drive Positions	59
2. HDD1 location only: Slide the power cables from the cable clip that is located on the top of the hard drive carrier.	59
3. Remove the screw that secures the hard drive bracket to the chassis (see letter \	59
Figure 29. Removing Drive Carrier from Server System	60
4. Position the drive with the drive connectors facing up, as shown in the following figure (Figure 30). Set the drive carrier o...	60
Figure 30. Installing Drive into the Drive Carrier	60
5. Set the drive assembly into place in the chassis. See letter \	61
6. Attach the drive assembly to the chassis with the screw you removed previously in step 3 (see letter \	61
Note: You must install the assembly that contains the optical drive bracket on the left side of the system.	61
Figure 31. Installing Drive Assembly into the Server System	61
7. HDD1 only: Route the power cable into the cable clip on the top of the hard drive bracket.	61
8. Connect the data cables to the drive(s).	61
a. If a drive is installed in the HDD0 carrier, connect the HDD0 data cable to the SATA 0 connector on the server board. See letter \	61
b. If a drive is installed in the HDD1 carrier, connect the HDD1 data cable to the SATA 1 connector on the server board. See letter \	61
Note: The data cables are factory routed underneath the fan module. Use caution to make sure you connect the cables between the server board and the hard drives. The cables are labeled at each end.	61
9. Connect the power cables to the drive(s):	61
a. If a drive is installed in the HDD1 carrier, attach the connector on the daisy chain power cable that is closest to the power supply to the HDD1 connector.	61
a. If a drive is installed in the HDD0 carrier, attach the middle connector on the daisy chain power cable to the HDD0 power connector.	62
Figure 32. Connecting Hard Driver Power and Data Cables	62
Removing a Fixed Hard Disk Drive	62
1. Disconnect the power and data cables from the drive.	62
2. HDD1 location only: Slide the power cable from the cable clip that is located on the top of the hard drive carrier.	62
3. Remove the screw that holds the hard drive bracket to the chassis (see letter \	62
Figure 33. Removing Drive Carrier from the Server System	63
4. Remove the four screws that attach the hard drive to the drive carrier. Lift the drive from the carrier. Store the drive in an anti-static bag.	63
5. If you are installing a new drive, skip the rest of these steps and instead see “Installing and Removing a Fixed Hard Drive”.	63
6. Insert the screws that held the drive in the carrier into the screw locations on the carrier for future use.	63
7. Set the drive assembly into place in the chassis (see letter \	63
Note: You must install the assembly that contains the optical drive bracket on the left side of the system.	63
Installing or Removing a Slimline Optical Drive	63
Caution: Slimline optical drives are NOT hot-swappable. Before removing or replacing the drive, you must first take the server o...	63
To maintain proper system cooling, if you do not install a device at this location, you must install the provided filler blank.	64
Installing a Slimline Optical Drive	64
Note: The hardware necessary to install your optical drive was shipped to you in a bag labeled “CD-ROM Assy”.	64
1. First time installation only: Remove the knockout in the bezel that corresponds to the opening for the optical drive by rocki...	64
Figure 34. Removing the Knockout in Bezel for Optical Opening	64
2. Attach the brackets to the optical drive using the four screws as shown in the following figure.	64
Figure 35. Attaching the Brackets to the Optical Drive	65
3. Slide the optical drive assembly in through the front of the chassis, as shown by letter \	65
Figure 36. Installing the Optical Drive into the Server System	65
Removing a Slimline Optical Drive	66
1. Remove the power and data cables.	66
2. Remove the screws and slide the optical drive assembly out of the chassis.	66
Figure 37. Removing the Slimline Optical Drive Assembly from the Server System	66
3. Remove the four screws from the brackets.	66
Figure 38. Removing the Brackets from the Slimline Optical Drive Assembly	66
Installing and Removing the PCI Riser Assembly	67
Removing the PCI Riser Assembly	67
1. Disconnect any cables attached to any add-in cards.	67
2. Grasp the riser assembly and pull up to release it from the system.	67
Figure 39. Removing the PCI Riser Assembly from the Server System	67
Installing the PCI Riser Assembly	67
1. Lower the riser assembly into place (see letter \	67
2. Align the two hooks in the riser assembly with the matching slots at the back of the server system (see letter \	67
Figure 40. Installing the PCI Riser Assembly	68
3. Press down uniformly until the two hooks on the rear of the PCI riser assembly engage the server system back panel slots. The riser card will seat into the matching socket on the server board. Ensure the riser card is fully seated.	68
Installing and Removing a PCI Add-In Card	68
Installing a PCI Add-In Card	68
1. After removing the PCI riser assembly from the server system, remove the screw that attaches the PCI bracket shield to the rear of the chassis to remove the shield. Retain the screw.	68
2. Insert the PCI card edge connector in the slot on the PCI riser.	68
Figure 41. Installing the PCI Riser Assembly from the Server System	69
Figure 42. Installing a PCI Card in a Riser Card	69
3. Insert the riser card with the attached PCI card into the PCI slot on the server board. Press firmly on the riser card until it is fully seated. Be sure to press down on the riser card, not on the PCI card.	69
Caution: Press the riser card straight down into the slot. Tipping the riser card while installing into the slot may damage the riser card or slot on the server board.	69
4. Use the screw removed in step 1 to secure the riser card assembly to the chassis.	69
Removing a PCI Add-In Card	69
1. Remove the screw holding the add-in card in place (see letter \	69
2. Remove the PCI add-in card from the riser card connector (see letter \	69
Figure 43. Removing a PCI Card in a Riser Card	70
Removing and Installing the System Blowers	70
Note: The fans that are integrated into the power supply cannot be replaced separately. If one of the fans in the power supply fails, you must replace the power supply.	70
Replacing the System Blower	70
1. Remove the processor air duct. For instructions, see “Removing the Processor Air Duct”.	70
2. Disconnect the two system blower cables from the server board. See letters \	71
Figure 44. Disconnecting the System Blower Cables	71
3. Remove the two screws that secure the fan bracket in place. Save these screws. You will re-install them later (see letter \	71
4. Remove the fan cable from beneath the clip at the front of the fan bracket (see letter \	71
5. Lift the fan bracket from the server. Lift the bracket at an angle, with the front of the bracket first, to clear the hard disk drive brackets (see letter \	72
Figure 45. Removing the Blower Bracket from the Server System	72
6. Turn the bracket over and remove the two screws that attach the failed fan to the fan bracket. Save these screws. You will reinstall them later. See letter \	72
Figure 46. Removing the System Blowers from the Bracket	72
7. Install the replacement blower onto the bracket, using the two screws you removed previously in step 3.	73
8. Set the blower assembly into the system. Insert the rear edge first and push the assembly slightly rearward to clear the hard disk drive brackets. Use caution to make sure you do not pinch any cables.	73
9. Route the cable from the blower at the right around the right side of the assembly and under the clip at the front of the blower bracket.	73
10. Secure the blower assembly to the system using the two screws you removed previously.	73
11. Connect the blower cables to the server board. See letters \	73
Figure 47. Connecting the System Blower Cables	73
Replacing the Server Board	74
Removing the Server Board	74
1. Remove the CPU air duct and air baffle.	74
2. If installed, remove the memory, processor heat sinks, and processors from the server.	74
3. If installed, remove the PCI riser assembly.	74
4. If installed, disconnect all SATA cables from the server board.	74
5. Remove the system PCI fan and blower cables.	74
6. Disconnect all power cables coming from the power supply to the server board.	74
7. Remove the seven screws from the server board (see letter \	74
Figure 48. Removing the Server Board	74
8. Install the replacement server board. See “Installing the Server Board” on page -53.	74
Installing the Server Board	75
1. Place the server board into the server system as shown in the following figure (see letter \	75
2. Attach the server board with seven screws (see letter \	75
Figure 49. Installing the Server Board	75
3. Re-connect all power cables coming from the power supply to the server board.	75
4. Re-connect the PCI Fan and blower cables.	75
5. Re-connect all SATA cables to the server board.	75
6. Install the PCI riser assembly.	75
7. Install the memory, processor heat sinks, and processors.	75
8. Install the CPU air duct and air baffle.	75
Replacing the Backup Battery	76
Warning: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the equipment manufacturer. Discard used batteries according to manufacturer's instructions.	76
Advarsel: Lithiumbatteri - Eksplosionsfare ved fejlagtig håndtering. Udskiftning må kun ske med batteri af samme fabrikat og type. Levér det brugte batteri tilbage til leverandøren.	76
Advarsel: Lithiumbatteri - Eksplosjonsfare. Ved utskifting benyttes kun batteri som anbefalt av apparatfabrikanten. Brukt batteri returneres apparatleverandøren.	76
Varning: Explosionsfara vid felaktigt batteribyte. Använd samma batterityp eller en ekvivalent typ som rekommenderas av apparattillverkaren. Kassera använt batteri enligt fabrikantens instruktion.	76
Varoitus: Paristo voi räjähtää, jos se on virheellisesti asennettu. Vaihda paristo ainoastaan laitevalmistajan suosittelemaan tyyppiin. Hävitä käytetty paristo valmistajan ohjeiden mukaisesti.	76
1. Observe the safety and ESD precautions at the beginning of this book.	77
2. Turn off all peripheral devices connected to the server. Turn off the server.	77
3. Disconnect the AC power cord from the server.	77
4. Remove the server's cover and locate the battery.	77
5. Insert the tip of a small flat bladed screwdriver, or an equivalent, under the tab in the plastic retainer. Gently push down on the screwdriver to lift the battery.	77
6. Remove the battery from its socket.	77
Figure 50. Replacing the Backup Battery	77
7. Dispose of the battery according to local ordinance.	77
8. Remove the new lithium battery from its package, and, being careful to observe the correct polarity, insert it in the battery socket.	77
9. Close the chassis.	77
10. Run Setup to restore the configuration settings to the RTC.	77
Replacing the Power Supply	77
Caution: The power supply is not hot-swappable. Before removing or replacing the power supply, you must first take the server ou...	77
Removing the Power Supply	77
1. Disconnect all power supply cables including power at rear of chassis (see letter “A”).	78
2. Remove the two screws securing the power supply to the back panel (see letter “B”).	78
3. Lift the power supply up to clear the chassis tab (see letter “C”) and remove the power supply by sliding it out (see letter “D”).	78
Figure 51. Removing the Power Supply from the Server System	78
Installing the Power Supply	78
1. Insert the replacement power supply by first engaging the back panel (see letter “A”).	78
2. Lower the front of the power supply into place behind the chassis tab (see letter “B”).	79
Figure 52. Installing the Power Supply into the Server System	79
3. Secure the power supply to the back panel with two screws (see letter “C”).	79
4. Connect all cables, including the power at the rear of the chassis (see letter “D”).	79
Installing and Removing the Rack Handles	79
Installing the Rack Handles	79
1. Align the rack handle with the holes on the side of the server system and attach the rack handle with the two screws.	79
Figure 53. Installing the Rack Handle	80
2. Repeat step 1 on the opposite side of the server.	80
Removing the Rack Handles	81
1. Remove the two screws holding the rack handle in place, and remove the rack handle from the server system.	81
Figure 54. Removing the Rack Handle	81
4 Server Utilities	83
Using the BIOS Setup Utility	83
Starting Setup	83
If You Cannot Access Setup	83
Setup Menus	83
Upgrading the BIOS	85
Preparing for the Upgrade	85
Recording the Current BIOS Settings	85
1. Boot the computer and press <F2> when you see the message:	85
2. Write down the current settings in the BIOS Setup program.	85
Note: Do not skip step 2. You need these settings to configure your server at the end of the procedure.	85
Obtaining the Upgrade	86
Note: Review the instructions and release notes provided in the readme file distributed with the BIOS image file before attempti...	86
Upgrading the BIOS	86
Caution: Do not power down the system during the BIOS update process! The system resets automatically when the BIOS upgrade process completes. Doing so may corrupt the system BIOS.	86
Note: You may encounter a CMOS Checksum error or other problem after reboot. If this happens, shut down the system and boot it again. CMOS checksum errors require that you enter Setup, check your settings, save your settings, and exit Setup.	86
Clearing the CMOS	86
1. Power down the system; do not disconnect the AC power.	86
2. Open the server.	86
3. Move the jumper from the normal operation position, CMOS Clear by MBX, at pins 1 and 2 to the CMOS Clear Force Erase position, covering pins 2 and 3.	86
Figure 55. CMOS Recovery Jumper	87
4. Reconnect the AC power and power up the system.	87
5. When the system begins beeping, power it down and disconnect the AC power.	87
6. Return the CMOS Clear jumper to the spare location, covering pins 1 and 2.	87
7. Close the server chassis; reconnect the AC power and power up the system.	87
8. The CMOS is now cleared and you can reset it by going into the BIOS setup.	87
Resetting the Password	87
1. Power down the system and disconnect the AC power.	87
2. Open the server chassis.	87
3. Move the jumper from the normal operation position, Password Clear Protect, at pins 1 and 2 to the Password Clear Erase position, covering pins 2 and 3.	87
Figure 56. Password Recovery Jumper	88
4. Reconnect the AC power; power up the system.	88
5. Power down the system and disconnect the AC power.	88
6. Return the Password Reset jumper to the Password Clear Protect position, covering pins 1 and 2. Reconnect AC power and power up the server.	88
7. The password is now cleared and you can reset it by going into the BIOS setup.	88
Appendix A: Technical Reference	89
400-W Single Power Supply Input Voltages	89
400-W Single Power Supply Output Voltages	89
1. Maximum continuous total DC output power should not exceed 400 W.	89
2. Peak total DC output power should not exceed 450 W.	89
3. Peak power and current loading is supported for a minimum of 12 seconds.	89
4. Combined 3.3 V and 5 V power should not exceed 80 W.	89
System Environmental Specifications	90
Appendix B: Intel® Server Issue Report Form	91
Note: For the fastest service, please submit your form via the Internet.	91
Board / Chassis Information	91
DIMM Configuration	92
Operating System Information	92
Add-in Card, Peripheral, Video, NIC	93
Hard Drive Information	94
Management Information	94
Complete Problem Description	94
Appendix C: LED Decoder	97
Figure 57. Diagnostic LED Placement Diagram	97
A. Status LED	97
B. ID LED	97
C. Diagnostic LED #7 (MSB LED)	97
D. Diagnostic LED #6	97
E. Diagnostic LED #5	97
F. Diagnostic LED #4	97
G. Diagnostic LED #3	97
H. Diagnostic LED #2	97
I. Diagnostic LED #1	97
J. Diagnostic LED #0 (LSB LED)	97
Appendix D: Getting Help	109
1. Visit the following Intel support web page: http://support.intel.com/support/motherboards/server	109
2. If you are still unable to obtain a solution to your issue, send an email to Intel’s technical support center using the online form available at http://supportmail.intel.com/scripts-emf/welcome.aspx	109
3. Lastly, you can contact an Intel support representative using one of the support phone numbers available at http://support.in...	109
Warranty Information	109
Appendix E: Regulatory and Compliance Information	111
Product Regulatory Compliance	111
Warning: To ensure regulatory compliance, you must adhere to the assembly instructions in this guide to ensure and maintain comp...	111
To help ensure EMC compliance with your local regional rules and regulations, before computer integration, make sure that the se...	111
This is an FCC Class A device. Integration of it into a Class B system does not result in a Class B device.	111
Product Safety Compliance	111
Intended Application	111
Product EMC Compliance - Class A Compliance	112
Note: Legally the product is required to comply with Class A emission requirements as it is intended for a commercial type market place. Intel targets 10db margin to Class A Limits	112
Certifications / Registrations / Declarations	112
Product Regulatory Compliance References	113
Electromagnetic Compatibility Notices	116
FCC Verification Statement (USA)	116
Industry Canada (ICES-003)	117
Europe (CE Declaration of Conformity)	117
VCCI (Japan)	117
BSMI (Taiwan)	117
Korean Compliance (RRL)	118
1. Type of Equipment (Model Name): On License and Product	118
2. Certification No.: On RRL certificate. Obtain certificate from local Intel representative	118
3. Name of Certification Recipient: Intel Corporation	118
4. Date of Manufacturer: Refer to date code on product	118
5. Manufacturer/Nation: Intel Corporation/Refer to country of origin marked on product	118
CNCA (CCC-China)	118
Product Ecology Compliance	118
Other Markings	121
Regulated Specified Components	122
End-of-Life / Product Recycling	123
Appendix F: Warranty	125
Limited Warranty for Intel® Chassis Subassembly Products	125
Extent of Limited Warranty	125
Limitations of Liability	126
How to Obtain Warranty Service	126
Telephone Support	127
Returning a Defective Product	127

Match case Limit results 1 per page

Intel® Server System SR1630BC Service Guide

xix

List of Figures

Figure 1. Intel

Server System SR 1630BC

...............................................................................

Figure 2. Cable Routing Drawing

..............................................................................................

Figure 3. System Components

..................................................................................................

Figure 4. Server Board Connector and Component Locations

.................................................

Figure 5. Configuration Jumper Location

................................................................................

Figure 6. Light Guided Diagnostic LEDs

.................................................................................

Figure 7. Back Panel Connectors

............................................................................................

Figure 8. Front Panel Control Panel - Intel

Server System SR1630BC

................................

Figure 9. Server System I/O Connector Locations

..................................................................

Figure 10. Optional Peripherals

...............................................................................................

Figure 11. DIMM Configuration Diagram

.................................................................................

Figure 12. Channel Slots Configuration

..................................................................................

Figure 13. Removing the Front Bezel

......................................................................................

Figure 14. Installing the Front Bezel

........................................................................................

Figure 15. Removing the Server System Cover

......................................................................

Figure 16. Installing the Server System Cover

........................................................................

Figure 17. Removing the Processor Air Duct

..........................................................................

Figure 18. Installing the Processor Air Duct

............................................................................

Figure 19. Installing the Memory

.............................................................................................

Figure 20. Lifting the Load Lever

.............................................................................................

Figure 21. Open the Load Plate

..............................................................................................

Figure 22. Remove the Socket Protective Cover

....................................................................

Figure 23. Remove the Processor Protective Cover

...............................................................

Figure 24. Installing the Processor

..........................................................................................

Figure 25. Close the Load Plate and Socket Lever

.................................................................

Figure 26. Protective Film Removal

........................................................................................

Figure 27. IU Reference Heat sink Assembly

.........................................................................

Figure 28. Locating Drive Positions

.........................................................................................

Figure 29. Removing Drive Carrier from Server System

.........................................................

Figure 30. Installing Drive into the Drive Carrier

.....................................................................

Figure 31. Installing Drive Assembly into the Server System

..................................................

Figure 32. Connecting Hard Drive Power and Data Cables

....................................................

Figure 33. Removing Drive Carrier from the Server System

...................................................

Figure 34. Removing the Knockout in Bezel for Optical Opening

...........................................

Figure 35. Attaching the Brackets to the Optical Drive

............................................................

Figure 36. Installing the Optical Drive into the Server System

................................................

Figure 37. Removing the Slimline Optical Drive Assembly from the Server System

..............

Figure 38. Removing the Brackets from the Slimline Optical Drive Assembly

........................

Figure 39. Removing the PCI Riser Assembly from the Server System

.................................

Figure 40. Installing the PCI Riser Assembly

..........................................................................

Figure 41. Installing the PCI Riser Assembly from the Server System

...................................

Figure 42. Installing a PCI Card in a Riser Card

.....................................................................