Invacare L-3XB Owners Manual - Page 52

Installing/Removing the Crutch/Cane Holder, Installing, Removing

Page 52 highlights

12 ACCESSORIES 12.1 Installing/Removing the Crutch/Cane Holder ƽ WARNING The installation of the crutch/cane holder onto the back of the scooter seat significantly increases the length of the scooter. When turning the scooter or swiveling the scooter seat, it is important to take note of this increased length - otherwise, injury and/or damage to the surrounding property may result.  For this procedure, refer to FIGURE 12.1. Installing 1. Install the crutch/cane holder into the accessory tube located on the back of the seat. 2. Install the mounting knob to secure the crutch/cane holder in place. Securely tighten. 3. Align the slot on the base with the hook on the crutch/cane holder and slide base down into position. Removing 1. Remove the crutch/cane holder from the accessory tube. 2. Remove the mounting knob that secures the crutch/cane holder in place. 3. Remove the crutch/cane holder from the accessory tube. Crutch Cane Holder Hook Base Accessory Tube Accessory Tube Mounting Knob Installs in One of These Locations Insert Into Accessory Tube Lynx™L-3X Scooter FIGURE 12.1 Installing/Removing the Crutch/Cane Holder 52 Part No. 1145807

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60

12
ACCESSORIES
Lynx™L-3X Scooter
52
Part No. 1145807
12.1
Installing/Removing the Crutch/Cane Holder
Installing
1.
Install the crutch/cane holder into the accessory tube located on
the back of the seat.
2.
Install the mounting knob to secure the crutch/cane holder in place.
Securely tighten.
3.
Align the slot on the base with the hook on the crutch/cane holder
and slide base down into position.
Removing
1.
Remove the crutch/cane holder from the accessory tube.
2.
Remove the mounting knob that secures the crutch/cane holder in
place.
3.
Remove the crutch/cane holder from the accessory tube.
FIGURE 12.1
Installing/Removing the Crutch/Cane Holder
±
WARNING
The installation of the crutch/cane holder onto the back of the scooter seat significantly increases the length of the scooter.
When turning the scooter or swiveling the scooter seat, it is important to take note of this increased length - otherwise,
injury and/or damage to the surrounding property may result.
For this procedure, refer to FIGURE 12.1.
Accessory
Tube
Base
Hook
Crutch Cane
Holder
Mounting Knob Installs in One
of These Locations
Insert Into
Accessory Tube
Accessory
Tube