JET Tools 690617 User Manual - Page 7

5.0 Specifications Model Number JTM-949EVS/230 JTM-1050EVS2 Stock Number 691500 691600 Motor and Electricals: Motor type TEFC TEFC Horsepower 3HP (2.24kW 3HP (2.24kW) Phase ...3 3 Voltage 230V only 230V only Cycle ...60Hz 60Hz Listed FLA (full load amps 8A 8A Motor Speed (RPM 1720 1720 Power transfer Pulley/gears Pulley/gears Sound Emission 1 (tested at 3.28 ft. from machine): Without load 72 72 With load 80 80 Head and Spindle: Spindle Taper R-8 R-8 Diameter of Quill 3.375 in. (85.75mm 3.375 in. (85.75mm) Number of Spindle Speeds Variable Variable Range of Spindle Speeds 60-500 / 500-4500 RPM 60-500 / 500-4500 RPM Downfeeds per Revolution of Spindle 0.0015, 0.003, 0.006 in 0.0015, 0.003, 0.006 in. Spindle Travel 5 in. (127mm 5 in. (127mm) Head Movement - Left and Right 90 deg 90 deg. Head Movement - Fore and Aft 45 deg 45 deg. Maximum Distance Spindle Nose to Table 20-3/4" (530mm 20-3/4 "(530mm) Maximum Distance Spindle Center to Column 18-1/8 (460mm 26-3/4 (681mm) Minimum Distance Spindle Center to Column 5.2" (132mm 5.9"(150mm) Collet Capacity 1/8 - 7/8 in 1/8 - 7/8 in Ram Travel, maximum 8-1/8"(206mm 17-3/8"(440mm) Table and Knee: Table Size 9 x 49 in. (229 x 1245mm)......... 10 x 50 in. (250x 1270mm) Longitudinal Table Travel, maximum 30-3/4" (784mm 29-7/8 (760mm Table Cross Travel, maximum 12 in. (305mm 14-3/4 (375mm) Number of T-Slots 3 3 T-Slot Size, width x depth 5/8 x 3/4 in. (15.9 x 19mm)......... 5/8 x 3/4 in. (15.9 x 19mm) T-Slot Centers 2-1/2 in. (63.5mm 2-1/2 in. (63.5mm) Table Load, maximum 660 lb (300 kg 840 lb (380 kg) Knee Travel, maximum 15-3/4 "(402mm 16-1/8 (412mm) Misc. Dimensions: Saddle width 20 in. (510mm 20 in. (510mm) Column width 11-3/8 in. (290mm 11-3/8 in. (290mm) Overall Dimensions, assembled 65-3/4 W x 63 D x 85-3/4 H in. (1670 x 1600 x 2178mm Weights: Net Weight, approx 2420 lb (1100 kg 2486 lb (1130 kg) Shipping Weight, approx 2552 lb (1160 kg 2618 lb (1190 kg) 1 The specified values are emission levels and are not necessarily to be seen as safe operating levels. As workplace conditions vary, this information is intended to allow the user to make a better estimation of the hazards and risks involved only. The specifications in this manual were current at time of publication, but because of our policy of continuous improvement, JET reserves the right to change specifications at any time and without prior notice, without incurring obligations. 7