JET Tools JWBS-18-3 User Manual - Page 15

Adjustments

Get JET Tools JWBS-18-3 PDF manuals and user guides View all JET Tools JWBS-18-3 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

7.0 Adjustments 7.1 Aluminum resaw fence Refer to Figures 7-1 and 7-2. Loosen knobs (A1) until lock bar protrudes enough on which to slide the aluminum fence plate from one end, as shown in Figure 7-1. Retighten knobs. Figure 7-1: vertical position The aluminum fence plate can be installed in one of two positions; vertically (resaw position), as shown in Figure 7-1; or horizontally as shown in Figure 72. Horizontal position is useful for smaller workpieces. (Zero setting of cursor cannot be used with horizontal fence position.) Figure 7-3 7.3 Table tilt Refer to Figure 7-4. 1. Disconnect machine from power source. 2. Loosen lock handle (D). 3. Tilt table up to 45 degrees to the right (as viewed from operator side), or up to 5 degrees to the left. 4. Tighten lock handle. Note: Table stop bolt (F, Figure 7-4) must be pivoted out of the way to tilt table to the left. Figure 7-4 Figure 7-2: horizontal position 7.2 Fence fine adjust Refer to Figure 7-3. 1. Loosen fence lock knob (A, Figure 7-3). 2. Loosen knob (B). 3. Slide fence to approximate position, based on the scale measurement aligning with the right side of resaw fence. 4. Tighten knob (B). 5. Rotate knurled knob (C) to achieve fine adjustment. 6. When setting is reached, tighten fence lock knob (A). 7.4 Adjusting 90-degree table stop Before adjusting the 90º table stop, the blade tension must be properly adjusted (see sect. 7.7) To adjust 90º table stop: 1. Loosen lock handle (D, Figure 7-4) and use knob (E) to tilt table until it rests against table stop bolt (F). Retighten lock handle. 2. Use a square (Figure 7-5) placed on table and against blade to verify that table is 90 degrees to blade. 3. If an adjustment is necessary, loosen lock handle (D). Tilt table until it is square to blade; then retighten lock handle. 4. Loosen lock nut (F1) and turn table stop bolt (F) until it contacts table. Tighten lock nut to hold table stop in place. When tightening the nut hold the table stop bolt in place with a wrench to prevent movement. 15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
15
7.0
Adjustments
7.1
Aluminum resaw fence
Refer to Figures 7-1 and 7-2.
Loosen knobs (A
1
) until lock bar protrudes enough
on which to slide the aluminum fence plate from one
end, as shown in Figure 7-1. Retighten knobs.
Figure 7-1:
vertical position
The aluminum fence plate can be installed in one of
two positions; vertically (resaw position), as shown
in Figure 7-1; or horizontally as shown in Figure 7-
2.
Horizontal position is useful for smaller workpieces.
(Zero setting of cursor cannot be used with
horizontal fence position.)
Figure 7-2:
horizontal position
7.2
Fence fine adjust
Refer to Figure 7-3.
1.
Loosen fence lock knob (A, Figure 7-3).
2.
Loosen knob (B).
3.
Slide fence to approximate position, based on
the scale measurement aligning with the right
side of resaw fence.
4.
Tighten knob (B).
5.
Rotate knurled knob (C) to achieve fine
adjustment.
6.
When setting is reached, tighten fence lock
knob (A).
Figure 7-3
7.3
Table tilt
Refer to Figure 7-4.
1.
Disconnect machine from power source.
2.
Loosen lock handle (D).
3.
Tilt table up to 45 degrees to the right (as
viewed from operator side), or up to 5 degrees
to the left.
4.
Tighten lock handle.
Note
: Table stop bolt (F, Figure 7-4) must be pivoted
out of the way to tilt table to the left.
Figure 7-4
7.4
Adjusting 90-degree table stop
Before adjusting the 90º table stop, the blade
tension must be properly adjusted (see sect. 7.7)
To adjust 90º table stop:
1.
Loosen lock handle (D, Figure 7-4) and use
knob (E) to tilt table until it rests against table
stop bolt (F). Retighten lock handle.
2.
Use a square (Figure 7-5) placed on table and
against blade to verify that table is 90 degrees
to blade.
3.
If an adjustment is necessary, loosen lock
handle (D). Tilt table until it is square to blade;
then retighten lock handle.
4.
Loosen lock nut (F
1
) and turn table stop bolt (F)
until
it contacts table. Tighten lock nut to hold
table stop in place. When tightening the nut hold
the table stop bolt in place with a wrench to
prevent movement.