JVC BD-X200U Instruction Manual - Page 61

Synchronous Recording Recording Playback Signals From a VCR with RS-422A RS-422A control can be used to record playback signals from a VCR with an RS-422A terminal to a disc in your BD-X200.It will also be possible to control that VCR using this DVD recorder's REMOTE CONTROL screen. Signal Connections VIDEO OUT VIDEO IN AUDIO IN VIDEO IN LINE OUT Y/C IN INPUT LEVEL AUDIO CH1 IN OUT 4dB 8dB AUDIO OUT LAN SIGNAL GND DV IN/OUT USB CH2 REMOTE DC 19V REMOTE USB terminal Keyboard AUDIO OUT VIDEO OUT AUDIO INPUT AUDIO MONITOR AUDIO INPUT / AUDIO MONITOR SELECT SDI CH1 CH2 CH3 CH4 AES/EBU L CH1 CH2 CH3 CH4 ANALOG R CH1 CH2 CH3 CH4 VIDEO INPUT SIF LINE CPN Variable Motion VIDEO CASSETTE RECORDER POWER ON I OFF O CH1 CH2 CH3 CH4/TRACKING R P dB OVER dB 0 +4 +2 -10 R P dB OVER dB 0 +4 +2 -10 R P dB OVER dB 0 +4 +2 -10 R P dB OVER dB 0 +4 +2 -10 0 -20 0 -20 0 -20 0 -20 -2 -30 -2 -30 -2 -30 -2 -30 -4 -40 -4 -40 -4 -40 -4 -40 -60 -60 -60 -60 PHONES CH1 CH2 CH3 REC CH4 CTL TC UB DF SERVO CF GEN 16:9 AP AUTO OFF P.READ V.VAR PB/EE REMOTE 525 CONDITION 625 COUNTER RESET UB MENU SET VCON REMOTE HOLD PB PB/EE H ASSEM VIDEO M DA1 DA2 S DA3 F DA4 EJECT REC PLAY PAUSE/STILL TRACKING IN ENTRY OUT INSERT TC TOP VIDEO AUDIO SEARCH VAR PLAYER RECORDER P.PLAY STILL X-1 X1 PULL RELEASE PULL FOR VARIABLE PLAY METER MODE FINE TRACKING STAND BY REW STOP FF CANCEL PREVIEW AUTO EDIT PREROLL SHIFT REVIEW USER SERVO/SYS TIME CODE ON SCREEN OTHERS REV PULL RELEASE FWD VCR with an RS-422A terminal MONITOR OUT Esc F1 F2 F3 F4 F5 F6 F7 F8 F9 F10 F11 F12 Print Screen Sysrq Scroll Lock Pause Break ʮ ʂ ʡ Ώ Α ʙ  Back 1 2 3 4 5 6 7 8 9 0 - ^ ˇ Space Tab Q WE R T Y U I O P ʆ ʮ Enter @ < Caps Lock Shift A S Zͭ D F X C G H J V B N K L M > ɻ ?ɾ ʊ  / Shift  Ctrl Alt Alt Ctrl Insert Home Page Up Delete End Page Down Num Lock  7 8 4 5 * 9 + 6 1 2 Enter 0 . Mouse Monitor Monitor ● Connect the RS-422A REMOTE terminal on the rear of the DVD recorder to the remote RS-422A terminal on the VCR using an RS-422A cable. ● Connect the DVD recorder's VIDEO LINE IN and AUDIO IN terminals to the VCR's video out and audio out terminals. ● Connect the DVD recorder's VIDEO LINE OUT and AUDIO OUT terminals to the monitor's video in and audio in terminals. ● A keyboard and mouse can be used as an alternative to the DVD recorder's buttons when using the REMOTE CONTROL screen. If used, these are to be connected to each of the USB terminals on the rear panel. Setup Procedures ● Insert the tape for playback into the VCR. Ensure that this tape contains an SMPTE time code. ● Insert a recordable disc into your BD-X200. Settings VCR : Enable control via RS-422A. BD-X200 : Set REMOTE SELECT from the REMOTE MENU screen to 9PIN (MASTER). REMOTE MENU screen REMOTE MENU MENU REMOTE SELECT REC CONTROL REM FF/REW MODE 9PIN(MASTER) OFF FF/REW ● When REMOTE SELECT is set to 9PIN (MASTER), the REMOTE CONTROL (9PIN MASTER) screen will appear. This screen is used to perform editing operations, and the corresponding operations are described on the following pages. REMOTE CONTROL (9PIN MASTER) screen REMOTE CONTROL SCREEN ( 9PIN MASTER ) EXIT IN POINT 00:00:00:00 OUT POINT 00:10:00:00 Note When pressing and holding the REC button more than 2 seconds while the DVD recorder is stopped, encoded output images can be checked while the button is being held. h: m: s : f 1 00:00:00:00 4 00:25:00:00 7 00:40:00:00 CHAPTER ADJ BITRATE TC SET TC CANCEL h: m: s : f 2 00:15:00:00 5 00:30:00:00 8 00:45:00:00 h: m: s : f 3 00:20:00:00 6 00:35:00:00 9 00:50:00:00 MANUAL TC INPUT :: 8.0 Mbps DISC REMAIN 000 min EDL LOAD EDIT/END FINALIZE 59