JVC BD-X200U Instruction Manual - Page 65

Recording Playback Signals From a DV Camera or VCR DV (IEEE1394) control can be used to record playback signals from a camera or VCR with a DV terminal to a disc in your BD-X200. It will then be possible to control that VCR using this DVD recorder's REMOTE CONTROL screen. Signal Connections Monitor Rear panel AUDIO OUT VIDEO OUT LAN SIGNAL GND VIDEO IN LINE OUT Y/C IN INPUT LEVEL AUDIO CH1 IN OUT 4dB 8dB DV IN/OUT USB CH2 REMOTE DC 19V DV IN/OUT terminal DV terminal (video, audio, and control signals) USB terminal DV cables: VC-VDV204 (2 m, 4P-4P) from JVC VC-VDV206 (2 m, 4P-6P) from JVC DV camera or VCR MIC 1 IN MIC 2 IN VIDEO OUT EARPHONE DV Y/C OUT LINE CH-2 OUT CH-1 VIDEO OUT Keyboard Esc F1 F2 F3 F4 F5 F6 F7 F8 F9 F10 F11 F12 Print Screen Sysrq Scroll Lock Pause Break ʮ ʂ ʡ Ώ Α ʙ  Back 1 2 3 4 5 6 7 8 9 0 - ^ ˇ Space Tab Q WE R T Y U I O P ʆ ʮ Enter @ < Caps Lock Shift A S D F Zͭ X C G H J V B N K L M > ɻ ?ɾ ʊ  / Shift  Ctrl Alt Alt Ctrl Insert Home Page Up Delete End Page Down Num Lock  7 8 4 5 1 2 0 * 9 + 6 Enter . Mouse Monitor ● Connect the DV IN/OUT terminal on the rear of your BD-X200 to the DV terminal on the DV camera or VCR using a DV (IEEE1394) cable. One of the commercially-available cables indicated above should be used for this purpose. ● Connect the DVD recorder's VIDEO LINE OUT and AUDIO OUT terminals to the monitor's video in and audio in terminals. ● A keyboard and mouse can be used as an alternative to the DVD recorder's buttons when using the REMOTE CONTROL screen. If used, these are to be connected to each of the USB terminals on the rear panel. Setup Procedures ● Insert the tape for playback into the camera or VCR. Ensure that this tape contains an SMPTE time code. ● Insert a recordable disc into your BD-X200. Settings DV camera or VCR : Enable control via DV. BD-X200 : Set REMOTE SELECT from the REMOTE MENU screen to DV (MASTER). REMOTE MENU screen REMOTE MENU MENU REMOTE SELECT REC CONTROL REM FF/REW MODE DV(MASTER) OFF FF/REW ● When REMOTE SELECT is set to DV (MASTER), the REMOTE CONTROL (DV MASTER) screen will appear. This screen is used to perform editing operations, and the corresponding operations are described on pages 60 through 62. REMOTE CONTROL (DV MASTER) screen REMOTE CONTROL SCREEN ( DV MASTER ) EXIT IN POINT 00:00:00:00 OUT POINT 00:10:00:00 Note When pressing and holding the REC button more than 2 seconds while the DVD recorder is stopped, encoded output images can be checked while the button is being held. h: m: s : f 1 00:00:00:00 4 00:25:00:00 7 00:40:00:00 CHAPTER ADJ BITRATE TC SET TC CANCEL h: m: s : f 2 00:15:00:00 5 00:30:00:00 8 00:45:00:00 h: m: s : f 3 00:20:00:00 6 00:35:00:00 9 00:50:00:00 MANUAL TC INPUT 8.0 Mbps DISC REMAIN ::: 000 min EDL LOAD EDIT/END FINALIZE 63