JVC DR-MV1S Instruction Manual - Page 42
Manual Timer Programing
View all JVC DR-MV1S manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 42 highlights
42 EN OPERATIONS ON DVD DECK Manual Timer Programing You can program this unit to timer-record as many as 8 programs. If you do not know the PlusCode number for the program you wish to record, use the following procedure to set your unit to timer-record the program. ● Make sure that the unit's built-in clock is set properly. ● Turn on the unit. ● Turn on the TV and select the video channel (or AV mode). ● Slide the TV/CABLE/DBS/DVD switch to DVD. DVD TIMER (#) VCR/DVD 7 PROG/CHECK ENTER 1 2 3 4 5 6 7 8 9 0 rtw e 1 Load a recordable disc. 2 Press VCR/DVD repeatedly so that the DVD lamp lights up on the unit. 3 Press PROG/CHECK to access the Program Check screen. ● When "PROGRAM FULL DELETE UNWANTED TIMER PROGRAM" appears on the TV screen, you need to cancel some of the reserved programs. (੬ pg. 45) 4 Press rt to select "NEW TIMER PROGRAM", then press ENTER. The program screen appears. 5 Press rt to set the desired date. ● The current date appears on the TV screen. The date you enter appears in its place. 6 Press w e to select "START", then press rt to set the desired start time. ● Each press of rt advances/goes back the start time in 1-min. increments. ● To advance/go back the start time in 30-min. increments, press and hold rt. 7 Press w e to select "STOP", then press rt to set the desired stop time. ● Each press of rt advances/goes back the stop time in 1-min. increments. ● To advance/go back the stop time in 30-min. increments, press and hold rt. 8 Press w e to select "CH", then press rt to select the desired channel. ● If you are using a DBS receiver, see "ATTENTION FOR DBS RECEIVER USERS" in the right column. 9 Set the other recording options as required. ● Refer to step 6 in "VCR Plus+® Timer Programing" (੬ pg. 41). 10 Press ENTER to access the Program Confirmation screen. 11 Press ENTER to complete timer programing. ● To program another timer, repeat steps 3 - 11. 12 Press DVD TIMER (#) to engage the unit's timer mode. The DVD timer lamp lights up on the unit and the VCR deck is automatically selected. When the VCR deck is in timer standby mode, the unit is automatically turned off. ● To disengage the timer mode, press DVD TIMER (#) again. NOTES: ● When two successive programs are recorded on a DVD-RW disc with Manual Timer Programing function, the beginning of the second one may be left off the recording. ● If the copy limited program is received during timer-recording, the unit enters Record Pause mode. Recording starts again if it is switched to a recordable broadcast during the time you programed. Cable Box and DBS Receiver Users To timer-record a satellite broadcast using Manual Timer Programing: A Perform "Cable Box and/or DBS Receiver Control Setting (DVD Deck Only)" (੬ pg. 22). B Perform "Manual Timer Programing" (੬ pg. 42). C Leave the cable box or DBS receiver's power on. ATTENTION FOR DBS RECEIVER USERS If you are using a DBS receiver (unless "DBS RECEIVER SET" is set to "OFF" ੬ pg. 22), the band indication (TV, CATV or DBS) appears on the left of the channel number indication. No indication: To timer-record a regular TV broadcast received on the unit. CATV: To timer-record a cable TV broadcast received on the unit, or through a cable box (unless "CABLE BOX SET" is set to "OFF" ੬ pg. 22). DBS: To timer-record a satellite broadcast received through a DBS receiver. NOTE: If the channel number entered requires that the band be set, "7=DBS" is displayed on the screen. If this happens, press the number key "7" to select "DBS".