JVC DR-MV1S Instruction Manual - Page 43

On-Disc Timer Programing On-Disc Timer Programing is a function used with discs that are especially intended for a specific program. The disc is then programed for a program you always watch every day or every week. Since older programs are automatically overwritten, a single DVD-RAM/RW (VR mode) disc can be used without worrying about how much recording capacity remains. (੬ pg. 44) You can program each disc to timer-record as many as 8 programs. ● Make sure that the unit's built-in clock is set properly. ● Turn on the unit. ● Turn on the TV and select the video channel (or AV mode). ● Slide the TV/CABLE/DBS/DVD switch to DVD. ATTENTION: ● On-Disc Timer Programing is possible only with the disc for On- Disc Timer Programing. ● If data is recorded on a disc for On-Disc Timer Programing using a unit from another manufacturer, On-Disc Timer Programing may no longer function properly. DVD TIMER (#) VCR/DVD PROG/CHECK ENTER 1 2 3 4 5 6 7 8 9 0 1 rtw e To Make The Disc For On-Disc Timer Programing 1 Load a recordable disc. 2 Press VCR/DVD repeatedly so that the DVD lamp lights up on the unit. 3 Press PROG/CHECK to access the Program Check screen. 4 When On-Disc Timer Programing is made for the first time on the disc Press rt to select "DISC TIMER PRGM", then press ENTER. ● When some programs are recorded on the disc, a caution message appears. In such a case, backup the programs as required, then format the disc before making On-Disc Timer Programing. (੬ pg. 78) When On-Disc Timer Programing has already been made on the disc Press rt to select "NEW TIMER PROGRAM", then press ENTER. 5 Press rt to set the desired date. ● The current date appears on the TV screen. The date you enter appears in its place. 6 Press w e to select "START", then press rt to set the desired start time. ● Each press of rt advances/goes back the start time in 1-min. increments. ● To advance/go back the start time in 30-min. increments, press and hold rt. OPERATIONS ON DVD DECK EN 43 7 Press w e to select "STOP", then press rt to set the desired stop time. ● Each press of rt advances/goes back the stop time in 1-min. increments. ● To advance/go back the stop time in 30-min. increments, press and hold rt. 8 Press w e to select "CH", then press rt to select the desired channel. ● If you are using a DBS receiver, see "ATTENTION FOR DBS RECEIVER USERS" (੬ pg. 42). 9 Set "DAILY/WEEKLY" option. ● Refer to step 6 in "VCR Plus+® Timer Programing" (੬ pg. 41). ● It is necessary to set "DAILY/WEEKLY" option for On-Disc Timer Programing. (੬ pg. 41, "Daily/Weekly Recording") 10 Set the other recording options as required. ● You can select XP, SP, LP, EP or FR480 mode for "REC MODE". However, you cannot select FR (JUST), FR60-FR360 and FR420. ● Refer to step 6 in "VCR Plus+® Timer Programing" (੬ pg. 41). ● It is not possible to use the Free Rate function. (੬ pg. 40) 11 Press ENTER to access the Program Confirmation screen. 12 Press ENTER to complete timer programing. ● To program another timer, repeat steps 3 - 12. Cable Box and DBS Receiver Users To timer-record a satellite broadcast using the On-Disc Timer Programing function: A Perform "Cable Box and/or DBS Receiver Control Setting (DVD Deck Only)" (੬ pg. 22). B Perform "On-Disc Timer Programing" (੬ pg. 43). C Leave the cable box or DBS receiver's power on. To Timer-record The Program With The Programed Disc 1 Load a programed disc. 2 Press DVD TIMER (#). The unit turns off and " " appears on the front display panel. The DVD timer lamp also lights up on the unit and the VCR deck is automatically selected. When the VCR deck is in timer standby mode, the unit is automatically turned off. ● To disengage the timer mode, press 1 again. NOTES: ● Even if On-Disc Timer Programing is overlapping with other timer programing, any caution message does not appear. In such a case, recording will be executed in the descending order of the recording start time of the program. ● On-Disc Timer Programing is not possible on a DVD-RW disc formatted in video mode. (੬ pg. 78) ● The information of a program recorded with On-Disc Timer Programing is not stored in the library. (੬ pg. 60) ● The play list is not created for the programs recorded with On-Disc Timer Programing. (੬ pg. 58) ● VCR Plus+ Timer Programing is not possible on the discs used exclusively for On-Disc Timer Programing. ● Manual Timer Programing is not possible on the On-Disc Timer Programed disc. (੬ pg. 42) ● Basic Recording is not possible on the On-Disc Timer Programed disc. (੬ pg. 38) ● The On-Disc Timer Programing function does not work on the unit form other manufactures even if the On-Disc Timer Programed disc is loaded. ● The beginning of a program may not be recorded. Also, if the 1st program's recording stop time and the 2nd program's recording start time is the same, the ending of the 1st program may not be recorded. ● If there is a power cut while recording, the recordings before the power cut are not guaranteed.