JVC DT-V24L3DU Instruction Manual - Page 9

7 Available signals The following signals are available for this monitor. Video signals No. Signal name 1 NTSC 2 PAL 3 B/W50 4 B/W60 5 480/60i 6 576/50i 7 480/60p 8 576/50p 9 640*480/60p 10 720/60p 11 720/50p 12 720/30p 13 720/25p 14 720/24p 15 1080/60i 16 1035/60i 17 1080/50i 18 1080/60p 19 1080/50p 20 1080/30p 21 1080/25p 22 1080/24p 23 1080/30psF 24 1080/24psF Signal format shown in the status display (☞ page 7) NTSC PAL B/W50 B/W60 480/60i 576/50i 480/60p 576/50p 640*480/60p 720/60p 720/50p 720/30p 720/25p 720/24p 1080/60i 1035/60i 1080/50i 1080/60p 1080/50p 1080/30p 1080/25p 1080/24p 1080/60i 1080/24psf VIDEO (INPUT1, INPUT2) Input terminal COMPO./RGB (Analog component/ Analog RGB)*1 E. AUDIO HD/ SD SDI (IN 1, IN 2)*2 - - - - - - - - √ √ √ √ √ - √ - - - √ √ √ √ √ √ √ √ √ √ √ √ √*3 √ √ √ - - - - √ √ √ √ √ √ √*3 √*3 √ √ DVI-D (HDCP) (Digital component/ digital RGB) 3 √: Acceptable -: Not acceptable *1 Analog component/analog RGB signals are compatible with G on sync signal, Y on sync signals, and composite sync signals (CS). The separate sync signal (HS/VS) is not compatible. *2 Compatible with EMBEDDED AUDIO signals *3 The signal is recognized as 1080/60i. Computer signals (preset) DVI-D (HDCP) terminals No. Signal name Resolution Horizontal Vertical 1 VGA60 640 480 2 WVGA60 852 480 3 SVGA60 800 600 4 XGA60 1024 768 5 WXGA (1280) 1280 768 6 WXGA+60 1440 900 7 SXGA60 1280 1024 8 WSXGA+60 1680 1050 9 UXGA60*4 1600 1200 10 WUXGA60*4 1920 1200 11 720/60p 1280 720 12 1080/60p*4 1920 1080 13 720/50p 1280 720 14 1080/50p*4 1920 1080 Frequency Horizontal (kHz) Vertical (Hz) 31.5 59.9 31.5 59.9 37.9 60.3 48.4 60.0 47.8 60.0 55.9 60.0 64.0 60.0 65.2 60.0 75.0 60.0 74.0 60.0 45.0 60.0 67.5 60.0 37.5 50.0 56.25 50.0 Scan system Non-interlace Non-interlace Non-interlace Non-interlace Non-interlace Non-interlace Non-interlace Non-interlace Non-interlace Non-interlace Non-interlace Non-interlace Non-interlace Non-interlace *4 For DT-V20L3D: When No. 9, 10, 12 or 14 signals come in, thin lines will become obscured because their signal resolution is higher than the screen resolution. • Non-preset signals may not be displayed normally even if their frequency is within the acceptable range (☞ "Horizontal/vertical frequency (computer signal)" on page 21). • When a preset signal comes in, the signal format is shown on the status display. For other signals, the resolution is shown. Specification of the DVI-D (HDCP) terminal Connect it to the DVI-D output terminal on a personal computer. Pin No. Input signal 1 T.M.D.S Data 2- 2 T.M.D.S Data 2+ 3 T.M.D.S Data 2 shield 4 NC 5 NC 6 DDC Clock 7 DDC Data 8 NC Pin No. Input signal 9 T.M.D.S Data 1- 10 T.M.D.S Data 1+ 11 T.M.D.S Data 1 shield 12 NC 13 NC 14 +5 V Power 15 GND 16 Hot Plug Detect Pin No. Input signal 17 T.M.D.S Data 0- 18 T.M.D.S Data 0+ 19 T.M.D.S Data 0 shield 20 NC 21 NC 22 T.M.D.S Clock shield 23 T.M.D.S Clock+ 24 T.M.D.S Clock- 9