JVC RX-8020VBK Instruction Manual - Page 122

English Operating Video Components IMPORTANT: To operate JVC's video components using this remote control: • You need to connect JVC's video components through the AV COMPU LINK jacks (see page 49) in addition to the connections using cables with RCA pin plugs (see pages 10 to 12). • Some JVC's VCRs can accept two types of the control signals- remote code "A" and "B." Before using this remote control, make sure that the remote control code of the VCR connected to the VCR 1 jacks is set to code "A." - When another JVC's VCR is connected to the VCR 2 or VIDEO terminals, set its remote control code to code "B." (This remote control cannot emit the control signals of code "B.") • When using the remote control, aim the remote control directly at the remote sensor on each component, not on the receiver. VCR 1 (VCR connected to the VCR 1 jacks) You can always perform the following operations: VCR1 :Turn on or off the VCR 1 (VCR connected to the VCR 1 jacks). After pressing VCR1 (or selecting "VCR1" by pressing CONTROL repeatedly), you can perform the following operations on the VCR 1 (VCR connected to the VCR 1 jacks): 1 - 9, 0 3 PLAY REW FF 7 STOP 8 PAUSE REC PAUSE CH +/- :Select the TV channels on a VCR. :Start playing. :Rewind a tape. :Fast wind a tape. :Stop playing or recording. :Pause playing. To resume press 3 PLAY. :Enter recording pause by pressing this button. To start recording again, press this button then 3 PLAY. :Change the TV channels on the VCR. A/V CONTROL RECEIVER Note: You can use either VCR1 or CONTROL to activate the buttons listed above. If you press VCR1, the playing source also changes. On the other hand, if you press CONTROL repeatedly to select "VCR1," the playing source does not change. CATV/DBS VCR1 TV AUDIO DVD DVD MULTI CD FM/AM TV/DBS VIDEO CDR PHONO VCR1 VCR2 TAPE/MD USB SURROUND DSP SURR/DSP ANALOG/DIGITAL OFF INPUT ANALOG DIRECT SOUND DIMMER ∗ ∗ BASS BOOST FRONT•L FRONT•R 1 2 3 MENU ∗ ∗ TEST CENTER SUBWFR 4 5 6 ENTER ∗ ∗ SURR•L SURR•R 7/P 8 9 ∗ ∗ ∗ MUTING DIGITALEQ SBACK•L SBACK•R 10 0 +10 RETURN FMMODE 100+ CATV/DBS CONTROL +++ CH/ LEVEL TV VOL VOLUME TV/VIDEO TEXT DISPLAY MENU PLAY EXIT REC PAUSE SLEEP /REW PAUSE FF/ SET DOWN - TUNING - UP STOP CONTROL RM-SRX8020J REMOTE CONTROL DVD player After pressing DVD or DVD MULTI, you can perform the following operations on a DVD player: 3 PLAY 4 ¢ 7 STOP 8 PAUSE :Start playing. :Return to the beginning of the current (or previous) chapter. :Skip to the beginning of the next chapter. :Stop playing. :Pause playing. To resume press 3 PLAY. After pressing DVD or DVD ∗FRONT•L ∗FRONT•R MULTI, these buttons can be used 2 3 for the DVD menu operations. TEST MENU ∗CENTER ∗SUBWFR 4 Note: For detailed menu operations, refer to the instructions supplied with the 5 6 ENTER ∗SURR•L 8 discs or the DVD player. Note: When you press one of the source selecting buttons, the operation mode appears on the display window. For example, the above illustration shows the remote control now works for VCR 1 operation. Buttons VCR1 DVD or DVD MULTI TV/DBS CONTROL (repeatedly)* Indications VCR1 DVD TV VCR1 CDDSC TAPE CDR * By pressing CONTROL repeatedly, you can select "VCR1," "TAPE," "CDR" or "CDDSC" as the source. TV You can always perform the following operations: TV TV VOL +/- TV/VIDEO :Turn on or off the TV. :Adjust the volume. :Set the input mode (either TV or VIDEO). After pressing TV/DBS, you can perform the following operations on a TV: CH +/- 1 - 9, 0, 100+ RETURN :Change the channels. :Select the channels. :Alternate between the previously selected channel and the current channel. 53