JVC RX-8020VBK Instruction Manual - Page 127

Press STANDBY/ON, Remote control does not work intendedly.

Get JVC RX-8020VBK - Dolby Digital EX Audio/Video Receiver PDF manuals and user guides
UPC - 046838258596
View all JVC RX-8020VBK manuals
Add to My Manuals
Save this manual to your list of manuals

Page 127 highlights

English PROBLEM "OVERLOAD" starts flashing on the display. POSSIBLE CAUSE Speakers are overloaded because of high volume. Speakers are overloaded because of short circuit of speaker terminals. The STANDBY lamp lights up after turning on the power, and soon the receiver turns off again (into standby mode). Remote control does not work. Remote control does not work intendedly. The receiver is overloaded because of high voltage. There is an obstruction between the remote sensor on the receiver and the remote control. Batteries are weak. An incorrect remote control operation mode is selected. SOLUTION 1.Press STANDBY/ON on the front panel to turn off the receiver. 2.Stop the playback source. 3.Turn on the receiver again and adjust the volume. Press STANDBY/ON on the front panel to turn off the receiver, then check the speaker wiring. If "OVERLOAD" does not disappear, unplug the AC power cord, then plug it back again. If speaker wiring is not short-circuited, contact your dealer. Press STANDBY/ON on the front panel to turn off the receiver. After unplugging the AC power cord, consult your dealer. Remove the obstruction. Replace batteries. (See page 15.) Select the correct remote control operation mode. (See pages 51 to 53.) 58

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
58
English
SOLUTION
1.Press STANDBY/ON
on the front panel to
turn off the receiver.
2.Stop the playback source.
3.Turn on the receiver again and adjust the volume.
Press STANDBY/ON
on the front panel to turn
off the receiver, then check the speaker wiring.
If
“
OVERLOAD
”
does not disappear, unplug the AC
power cord, then plug it back again.
If speaker wiring is not short-circuited, contact your
dealer.
Press STANDBY/ON
on the front panel to turn
off the receiver. After unplugging the AC power
cord, consult your dealer.
Remove the obstruction.
Replace batteries. (See page 15.)
Select the correct remote control operation mode.
(See pages 51 to 53.)
PROBLEM
“
OVERLOAD
”
starts flashing on the
display.
The STANDBY lamp lights up after
turning on the power, and soon the
receiver turns off again (into standby
mode).
Remote control does not work.
Remote control does not work intendedly.
POSSIBLE CAUSE
Speakers are overloaded because of
high volume.
Speakers are overloaded because of
short circuit of speaker terminals.
The receiver is overloaded because of
high voltage.
There is an obstruction between the
remote sensor on the receiver and the
remote control.
Batteries are weak.
An incorrect remote control operation
mode is selected.