JVC SR-MV30U Instruction Manual - Page 23
Initial Settings, Dbs Receiver Brand
View all JVC SR-MV30U manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 23 highlights
8 Select the output channel. Your selection depends on how the cable box or DBS receiver is connected to your unit. ● If the cable box or DBS receiver is connected to your unit's VHF/ UHF IN (DVD) connector on the rear panel, press rt to select the channel number representing the cable box's output (CH2 - CH9), then press ENTER. ● If the cable box or DBS receiver is connected to your unit's AUDIO/VIDEO Input connectors on the front panel, press rt to select "F-1", then press ENTER. ● If the cable box or DBS receiver is connected to your unit's AUDIO/VIDEO INPUT connectors on the rear panel, press rt to select "L-1", then press ENTER. ● If you do not use a cable box or DBS receiver, press rt to select "OFF", then press ENTER. 9 Enter the cable box's brand. 10 Press rt to select "CABLE BOX BRAND" or "DBS RECEIVER BRAND", then press ENTER. Press rt to select the brand code from the following list, then press ENTER. 11 Press rt to select "TEST MODE", then press ENTER. CABLE BOX BRAND ARCHER CABLETENNA CABLEVIEW CITIZEN CURTIS DIAMOND GC BRAND GEMINI GENERAL INSTRUMENTS HAMLIN JASCO JERROLD NOVAVISION OAK PANASONIC PULSER RCA REGAL REMBRANDT SAMSUNG SCIENTIFIC ATLANTA SIGMA SL MARX SPRUCER STARGATE TELEVIEW TOCOM UNIKA UNIVERSAL VIDEOWAY ZENITH CODE 1, 5, 17 1, 17 15, 16, 17, 21, 25 15, 16, 17, 21, 25 2, 8 1, 17 15, 16, 17, 21, 25 15 1, 4, 6, 11, 12, 15, 28 10, 18, 23 15 1, 4, 6, 11, 12, 15, 28 2, 8 7, 20 13, 14 15, 16, 17, 21, 25 13, 14 10, 18, 23 1, 16, 17 5, 16, 24 2, 8 7, 20 5, 16, 17, 24, 25 13, 14 5, 15, 16, 17, 21, 24, 25 5, 16, 24 1, 4, 16 1, 17 16, 17, 25 3, 9, 22 3, 9, 22 DBS RECEIVER BRAND JVC (DISH Network) ECHOSTAR (DISH Network) SONY (DSS) RCA (DSS) CODE 51 51 41 40 INITIAL SETTINGS EN 23 8 For cable box If the cable box's channel changes to 9, setting is complete. Press ENTER and "CABLE BOX CONTROL IS ON" appears on the screen for about 5 seconds, then the screen in step 6 appears. If the cable box's channel does not change to 9; A Press w e to select "NO", then press ENTER. B Repeat step 10 - 11 until the cable box's channel changes to 9 by entering another code. C If the channel does not change after going through all the code numbers listed for your model of cable box, then try all the other numbers. 8 For DBS receiver If the DBS receiver's channel changes to the channel listed below for your brand, setting is complete. Press ENTER and "DBS RECEIVER CONTROL IS ON" appears on the screen for about 5 seconds, then press ENTER. The screen in step 6 appears. JVC ] 100 ECHOSTAR ] 100 SONY RCA ] 205 ] 205 If the DBS receiver's channel does not change as shown above; A Press w e to select "NO", then press ENTER. B Repeat step 10 - 11. NOTES: ● The Controller may not work with all types of cable box or DBS receiver. ● If your cable box does not respond to any code between 1 and 28, you cannot use the Controller to change cable box channels. In this case, make sure to leave the cable box turned on and tuned to the proper channel before the scheduled start time of timer recording. Contact your cable company about the possibility of exchanging your current cable box with the one compatible with your unit. ● If your DBS receiver does not respond to the code, you cannot use the Controller to change satellite channels. In this case, make sure to leave the DBS receiver turned on and tuned to the proper channel before the scheduled start time of timer recording. ● The unit can only change the cable box or satellite channel through the Controller during timer recording. ● If your cable box or DBS receiver cannot be operated with a remote control (because it has no receiving window), you cannot use the Controller to change its channels. Make sure to leave the cable box or DBS receiver turned on and tuned to the proper channel before the scheduled start time of timer recording. ● If the unit's memory backup expires because of a power failure, set the cable box or DBS receiver output channel and brand again. ● For customers in U.S.A.: If you are unable to set the Controller, contact JVC toll free at 1-800-252-5722.