JVC UX-GN6 Instructions - Page 1
JVC UX-GN6 - Micro System Manual
![]() |
UPC - 046838037924
View all JVC UX-GN6 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 1 highlights
MICRO COMPONENT SYSTEM UX-GN6 -Consists of CA-UXGN6 and SP-UXGN5 Thank you for purchasing a JVC product. INSTRUCTIONS Warnings, Cautions and Others Mises en garde, précautions et indications diverses The lightning flash with arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the products enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. IMPORTANT FOR LASER PRODUCTS 1. CLASS 1 LASER PRODUCT 2. CAUTION: Do not open the top cover or cabinet. There are no user serviceable parts inside the unit; leave all servicing to qualified service personnel. 3. CAUTION: Visible and/or invisible class 1M laser radiation when open. Do not view directly with optical instruments. 4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED INSIDE THE UNIT. IMPORTANT POUR PRODUITS LASER 1. PRODUIT LASER CLASSE 1 2. ATTENTION: N'ouvrez pas le couvercle supérieur ni le coffret de l'appareil. Il n'y a aucune pièce réparable par l'utilisateur à l'intérieur de l'appareil; confiez toute réparation à un personnel qualifié. 3. ATTENTION: Rayonnement laser visible et/ou invisible de classe 1M une fois ouvert. Ne pas regarder directement dans le faisceau avec des instruments optiques. 4. REPRODUCTION DE L'ÉTIQUETTE: ÉTIQUETTE DE PRÉCAUTION PLACÉE À L'INTERIEUR DE L'APPAREIL. CAUTION: Proper Ventilation To avoid risk of electric shock and fire, and to prevent damage, locate the apparatus as follows: 1. Front: No obstructions and open spacing. 2. Sides/Top/Back: No obstructions should be placed in the areas shown by the dimensions below. 3. Bottom: Place on the level surface. Maintain an adequate air path for ventilation by placing on a stand with a height of 10 cm or more. ATTENTION: Aération correcte Pour prévenir tout risque de décharge électrique ou d'incendie et éviter toute détérioration, installez l'appareil de la manière suivante: 1. Avant: Bien dégagé de tout objet. 2. Côtés/dessus/dessous: Assurez-vous que rien ne bloque les espaces indiqués sur le schéma ci-dessous. 3. Dessous: Posez l'appareil sur une surface plane et horizontale. Veillez à ce que sa ventilation correcte puisse se faire en le plaçant sur un support d'au moins dix centimètres de hauteur. Front/Face Side/Côté LVT1989-001A[J/C] 0209RYMMDWDAT ©2009 Victor Company of Japan, Limited For customer use: Enter below the Model No. and Serial No. which are located either on the rear, bottom or side of the cabinet. Retain this information for future reference. Model No. Serial No. For U.S.A. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Le symbole de l'éclair à l'intérieur d'un triangle équilatéral est destiné à alerter l'utilisateur sur la présence d'une "tension dangereuse" non isolée dans le boîtier du produit. Cette tension est suffisante pour provoquer l'électrocution de personnes. Le point d'exclamation à l'intérieur d'un triangle équilatéral est destiné à alerter l'utilisateur sur la présence d'opérations d'entretien importantes au sujet desquelles des renseignements se trouvent dans le manuel d'instructions. CAUTION: Changes or modifications not approved by JVC could void the user's authority to operate the equipment. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION To reduce the risk of electrical shocks, fire, etc.: 1. Do not remove screws, covers or cabinet. 2. Do not expose this appliance to rain or moisture. ATTENTION Afin d'éviter tout risque d'électrocution, d'incendie, etc.: 1. Ne pas enlever les vis ni les panneaux et ne pas ouvrir le coffret de l'appareil. 2. Ne pas exposer l'appareil à la pluie ni à l'humidité. CAUTION The button in any position does not disconnect the mains line. Disconnect the mains plug to shut the power off completely (the STANDBY lamp goes off). The MAINS plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable. • When the System is on standby, the STANDBY lamp lights red. • When the System is turned on, the STANDBY lamp goes off. The power can be remote controlled. ATTENTION La touche , quelle que soit sa position, ne coupe pas la ligne principale. Débrancher la fiche principale pour couper complètement l'alimentation du secteur (le témoin STANDBY s'éteint). La fiche secteur ou un coupleur est utilisé comme dispositif de déconnexion de l'appareil, et l'appareil déconnecté doit être prêt à être utilisé. • Quand l'appareil est en mode d'attente, le témoin STANDBY est allumé en rouge. • Quand l'appareil est sous tension, le témoin STANDBY s'éteint. L'alimentation peut être commandée à distance. CAUTION: Excessive sound pressure from earphones or headphones can cause hearing loss. ATTENTION: Une pression acoustique excessive des écouteurs ou du casque d'écoute peut entraîner une perte auditive. CAUTION: Battery shall not be exposed to excessive heat such as sunshine, fire, or the like. ATTENTION: Les piles ne doivent en aucun cas être exposées à une chaleur excessive (lumière du solei, feu, etc.). 1 CA-UXGN6 SP-UXGN5 SP-UXGN5 CA-UXGN6 CAUTION: • Do not block the ventilation openings or holes. (If the ventilation openings or holes are blocked by a newspaper or cloth, etc., the heat may not be able to get out.) • Do not place any naked flame sources, such as lighted candles, on the apparatus. • When discarding batteries, environmental problems must be considered and local rules or laws governing the disposal of these batteries must be followed strictly. • Do not expose this apparatus to rain, moisture, dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus. ATTENTION: • Ne bloquez pas les orifices ou les trous de ventilation. (Si les orifices ou les trous de ventilation sont bloqués par un journal un tissu, etc., la chaleur peut ne pas être évacuée correctement de l'appareil.) • Ne placez aucune source de flamme nue, telle qu'une bougie, sur l'appareil. • Lors de la mise au rebut des piles, veuillez prendre en considération les problèmes de l'environnement et suivre strictement les règles et les lois locales sur la mise au rebut des piles. • N'exposez pas cet appareil à la pluie, à l'humidité, à un égouttement ou à des éclaboussures et ne placez pas des objets remplis de liquide, tels qu'un vase, sur l'appareil. [European Union only] [Union européenne seulement] Basic and Common Operations The operations on pages 4 to 6 are explained using the remote control, unless mentioned otherwise. However, if the System has the same or similar button names, they can also be used for the operations. Remote sensor STANDBY lamp Point at the remote sensor on the front panel. To Turn on or off (standby) the power Select a source Press Main unit Remote Indication/Result The STANDBY lamp on the System turns off/on. See "Playing Back a Disc/USB Mass Storage Class Device" on page 4. Adjust the volume See "Listening to an iPod/Viewing Images on the iPod" on page 5. Press repeatedly to select "FM," "AM," or "AUDIO IN" as the source. • See "Listening to FM and AM Broadcasts" or "Listening to Other Equipment" on page 5. - PHONES jack Stereo mini plug cord Headphones (not supplied) Display Demonstration When you plug in the System, the display demonstration automatically starts. To cancel the display demonstration, press and hold DEMO until "DEMO CLR" is displayed while the System is on standby. • When the ECO Mode is activated, the display demonstration does not work (and you cannot deactivate it). • When the display demonstration is activated, it also starts if no operation is done for about 2 minutes while the System is turned on. Laser Touch Operation You can use 4/¢ and VOL +/- on the front panel by sliding your finger up or down on the illumination. To use 4/¢ To use VOL +/- Using Headphones Be sure to turn down the volume before connecting or putting on the headphones. • Connecting the headphones will deactivate the speakers. • Sound adjustments also affect the sound through the headphones. Motion Sensor on the Front Panel When you move your hand close to the front panel while the System is on standby, the controls on the front panel illuminate. • When no operation is done for about 5 seconds, the illumination turns off. • When the ECO Mode is activated, the motion sensor does not work. Touch to turn on the System. 3 Drop the volume in a moment - Select the Sound Mode - To restore the volume, press again, or adjust the volume level. Press repeatedly to select the desired Sound Mode. The SOUND indicator lights up. Emphasize the sound (Sound Turbo) Reinforce the bass sound (Hyper Bass Sound) - Change the display brightness Turn off the display while on standby (canceled) The S.TURBO indicator lights up. To cancel this function, press again. The HBS indicator lights up. • When Sound Turbo function is activated (see above), the HBS indicator goes off and HBS button does not work. To cancel this function, press again. Press repeatedly when the System is turned on. (canceled) Press repeatedly while the System is on standby. Clock DISP OFF: Turns off the display with the motion sensor on. ECO ON: Turns on the ECO (Ecology) Mode. ECO Mode reduces power consumption while the System is on standby by turning off the display and motion sensor. NOTE: DO NOT turn off (standby) the System with the volume set to an extremely high level; otherwise, the sudden blast of sound can damage your hearing, speakers and/or headphones when you turn on the System or start playback. Getting Started Supplied Accessories After unpacking, check to be sure that you have all the following items. • Remote control, RM-SUXGN6J (× 1) • Lithium coin battery (× 1: installed in the remote control) • AM loop antenna (× 1) • FM antenna (× 1) • Video cord (× 1) If anything is missing, consult your dealer immediately. Prepare the Remote Control When you use the remote control for the first time, pull out the insulation sheet. Connections To a wall outlet Plug the AC power cord only after all connections are complete. Rear view Insulation sheet To Replace the Battery in the Remote Control Lithium coin battery (product number: CR2025) NOTES: • Store the battery in a place where children cannot reach. If a child accidentally swallows the battery, consult a doctor immediately. • To prevent the battery from overheating, cracking, or starting a fire: - Do not recharge, short, disassemble or heat the battery or dispose of it in a fire. - Do not leave the battery with other metallic materials. - Wrap the battery with tape and insulate when throwing away or saving it. - Do not poke the battery with tweezers or similar tools. • Dispose of battery in the proper manner, according to federal, state, and local regulations. For USA-California Only This product contains a CR Coin Cell Lithium Battery which contains Perchlorate Material - special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. To connect the FM antenna (supplied) Extend it so that you can obtain the best reception. FM antenna (supplied) To assemble the AM loop antenna (supplied) AM loop antenna (supplied) For iPod To connect the monitor (not supplied) -To view video/picture from the iPod Do not connect the AC power cord until all other connections have been made. Video cord (supplied) Monitor To connect the speaker cords Playing Back a Disc/USB Mass Storage Class Device This System can play back... - CD. - CD-R/CD-RW recorded in audio CD format (CD-DA) or recorded MP3/WMA files in ISO 9660 format. - USB mass storage class device containing MP3/WMA files. • When playing back an MP3 or WMA track, corresponding indicator lights up. Loading a Disc (on the System only) 1 Touch to open the disc tray. 2 • When using an 8 cm (3 3/16 inch) disc, place it on the inner circle of the disc tray. Basic Disc/USB Mass Storage Class Device Operations To Play back the disc Press Indication/Result • During playback, press again to pause. Play back the USB mass storage class device Stop playback Select a track • While playback is stopped, total track number and total playing time (for MP3/WMA files, group number and track number) appear. Select the next tracks. For better FM reception Disconnect the supplied FM antenna, and connect to an outdoor FM antenna using a 75 Ω wire with coaxial type connector. Outdoor FM antenna (not supplied) To connect the AM loop antenna Turn the AM loop antenna until the best reception is obtained. 2 Press and hold 3 Touch to close the disc tray. Release Red Insert Red Connecting a USB Mass Storage Class Device You can connect a USB mass storage class device such as a USB flash memory device, MP3 player, multimedia card reader, etc. to the System. Front view USB cable (not supplied) USB memory (not supplied) Black Black From right From left or speaker speaker NOTES: • Make sure the antenna conductors do not touch any other terminals, connecting cords and power cord. Also, keep the antennas away from metallic parts of the System, connecting cords, and the AC power cord. This could cause poor reception. • Keep the AM loop antenna cable wrapped around the AM loop antenna frame, otherwise the effectiveness and sensitivity of the AM loop antenna may be reduced. • Make sure both the speakers are connected correctly and firmly. • When connecting the speaker cords, match the polarity of the speaker terminals: red color to (+) and black color to (-). • DO NOT connect more than one speaker to each terminal. • DO NOT allow the conductor of the speaker cords to be in touch with the metallic parts of the System. NOTES: • When connecting with a USB cable, use the USB 2.0 cable whose length is less than 1 m (3.3 ft). • USB mass storage class device is charged through the USB terminal when the System is turned on and the source is "USB." • You cannot connect a computer to the USB terminal of the System. • Do not disconnect the USB mass storage class device when the System is turned on. It may cause malfunction of both this System and the device. • Noise and static electricity may stop the USB mass storage class device sound. In this case, disconnect the USB mass storage class device and connect it again after turning off the System. • Depending on the shape of USB mass storage class device, the USB terminal may not be fully inserted into the USB terminal on the System. In such a case, use a USB extension cable (not supplied) to connect. Prohibiting Disc Ejection (on the System only) You can lock the disc tray so that no one can eject the loaded disc. While the System is on standby... To cancel the prohibition, repeat the same procedure. Select a group (MP3/WMA only) To go back to the beginning of the current or previous tracks. Select the next groups. Select the previous groups. Forward search/ Reverse search Change the display information Press and hold to fast-forward the track during playback. Press and hold to fast-reverse the track during playback. (only for USB) Press repeatedly. NOTES: • If no disc is inserted or no USB mass storage class device is connected, "NO DISC" or "NO USB" appears on the main display. • If MP3/WMA files are not recorded on the disc or in the USB mass storage class device, "NO PLAY" appears on the main display. Playing Repeatedly-Repeat Play 1 Press repeatedly to specify the repeat mode as follows: RPT TRK: Repeats the current (or specified) track. [ 1] RPT GRP: Repeats all tracks in the current group (MP3/WMA only). [ ] RPT ALL: Repeats all tracks. [ ALL] RPT OFF: Normal playback 2 or 4 Programming the Playing Order-Program Play (only for Disc) 1 Select disc as the source. 2 Activate the Program Play. 3 or Select tracks you want for Program Play. • For MP3/WMA files only: You can also use UP or DOWN. 4 Press to store the selected track. 5 Repeat steps 3 and 4 to program other tracks you want. • If you try to program a 33rd track, "PGM FULL" appears. 6 The tracks are played back in the programmed order. Operations for Program Play (while not playing) • To check the programmed contents, press 4 or ¢. • To add tracks, repeat steps 3 and 4 above. • To erase the entire program, press and hold CANCEL for about 2 seconds. • To exit from Program Play, press PROGRAM or 7. - The stored program is kept. Playing at Random-Random Play (only for Disc) 1 Select disc as the source. 2 Press repeatedly to select the desired Random Mode. RANDOM: Plays all tracks in random order. [ALL RND] RND GRP: Plays tracks in the current group in random order. (MP3/WMA only). [ RND] RND OFF: Normal playback 3 Playback starts in random order. Operations for Random Play • To skip a track, press ¢. • To go back to the beginning of the current track, press 4.
![](/manual_guide/products/jvc-uxgn6-instructions-bc79ebe/1.png)