Jabra GN9125 Reference Guide - Page 3

3. Remote handset lifting functionality Answering and making telephone calls with GN1000 You may purchase a GN1000 as an accessory, which lets you answer and end telephone calls while away from your desk. Please contact your vendor or visit www.jabra.com for further information. To answer a call using the GN1000 or electronic hook switch functionality: 1. Remove the headset from the base unit when you receive a call. The link will be established and the on-line indicator on the front of the base unit will begin to flash. Note: If you are already wearing the headset, simply press the multifunction button on the headset momentarily to answer the incoming call. To end the call, press the multifunction button momentarily or place the headset in the base unit. Making telephone calls using the GN1000 or electronic hook switch functionality: To make a telephone call using the GN1000: 1. Remove the headset from the base unit. The link will be established and the on-line indicator on the front of the base unit will begin to flash. 2. Dial the desired number. To end the call, press the multifunction button momentarily or place the head- set in the base unit. Note: The connection cord must be connected to your telephone's handset port (not the headset port) in order for the GN1000 to function. GN9120/GN9125 with Electronic Hook Switch (EHS) The GN9120/GN9125 comes in versions which enables you to answer and end calls while away from your desk - without using the GN1000. This is, however, only possible on certain telephone systems. In order to determine which telephones have the EHS feature enabled, please refer to our website www.jabra.com. Please also refer to your telephone's user manual for clarification. 3 modes are available: • The RHL interface (non-EHS; works with the GN1000) • The DHSG interface (for example, with Siemens and Elmeg desk telephones) • The AEI interface (for example, with Tenovis desk telephones) Note: By default, the EHS-version of the GN9120/GN9125 is set to the DHSG interface. To toggle between DHSG, AEI and RHL interface, complete the following: 1. Place the headset in the base with its on-line indicator facing you. 2. Press the volume + and volume - buttons on the headset simultaneously for 6 seconds while the - + headset is in the base, until the headset's on-line indicator flashes rapidly. 3. You are now in interface switching mode, and can set the GN9120/GN9125 to work with your tel- RHL DSHG AEI ephone's interface. 4. Using the volume + button to move right and the volume - button to move left, select the required EHS interface. The base unit's 3 indicators show which interface the GN9120/GN9125 is in. See the illustration to Volume button Link icon Mute icon Charge icon  determine the type of interface. Note: If more than 15 seconds elapses without pressing the volume + or volume - buttons, the last selected interface will be activated. 5. To exit the interface switching mode, press the volume + and volume - buttons simultaneously for 6 seconds. 6. Only with the GN1000: Complete the setting up procedure according to its Quick Guide. 4. Audio and visual indicators The GN9120/GN9125's headset and base have audio and visual indicators, which represent various actions and aspects associated with setting up and operating the product. The headset gives audio and visual indications. The base gives various visual indications via its online, link and general indicators. Familiarize yourself with these indicators to fully benefit from your GN9120/GN9125. The headset's audio indicators: Headset action Out of range Mute ON Low Battery Charge Adjusting Volume Maximum Volume reached Minimum Volume reached Tone control adjustment Adding a headset at conference call Incoming call Audio indication Beep every 10 sec. Beep every 15 sec. Beep every 20 sec. Low single tone per press Short beep Short beep Beep (indicating 6 sec. has passed) Beep in master headset Beep (only if using GN1000) The headset's visual indicators: Headset mode Low Power mode Transmit volume adjustment Headset indicator Flashes rapidly when switching between modes Flashes rapidly when switching between modes The base's visual indicators: Base's on-line indicator On-line indicator Charging in Process Battery charging indicator flashes Charging completed Battery charging indicator ON Mute Mute indicator ON Low Power Mode Link-up indicator flashes every 10 sec. Adding a headset to conference call All lights are flashing, followed by battery indicator ON Link between headset and base Link-up indicator ON EHS (Electronic Hook Switch) setting Please refer to separate section Pairing of Headset and Base All lights are flashing for approx. 4 sec., followed by battery indicator ON On a call On-line indictor flashes