Jenn-Air JJW2427DS Dimension Guide - Page 4

JENN-AIR® DETAILED PLANNING DIMENSIONS 27" SINGLE WALL OVENS - FLUSH INSTALLATION JJW2427D - 27" x 297⁄8" x 245⁄16" (depth without handle) 4 of 5 OPENING/CLEARANCE DIMENSIONS 3/4" (1.9 cm) Top Cleat* 3/4" (1.9 cm) Top Cleat* A A B B A C D C D H 3/4" (1.9 cm) ToIp Cleat* I A 11/16" (1.7 cm) B 3/4" (1.9 cm) 1111//1166"" ((11..77 ccmTmo))p Cleat1*1/16" (1.7 cm) Side Cleat* 1/2" x 2" (1.3CSSxiiddA5ee.1CDClclBeem1a/a2t)t"**x 2" Side Cleat* (1.3 x 5.1 cm) C Spacer (entire deptShpacer (entire depth of cutout) 11/16" (1o.7f ccumto) ut) 11/16" (1.7 cm) D Side Cleat* Side Cleat* e e 11/16" (1.7 cm) Side Cleat* S11i/So1d1/6pf2e""ac(Cxuce1let.2e7ora"u(ct(et*m1)n.3)tirxe 5.1 cm) depth e 1/2" x 2" (1.3 x 5.1 cm) Sopf aceucetor u(et)ntire depth E eE e e E E FRONT VIEW e e 3/4" (1.9 cm) 3/4" (1.9 cm) e Top Cleat* Top Cleeat* A A A B B C De C D 3/4" (1.9 cm) Top Cleat* A 11/16" (1.7 cm) B Side Cleat* S1S111i/i/d1d166e"e" (C(C11ll.e.e77aactct*mT3*m/o4))"p(1C.l9eactS1m*1i/d1)6e" (1.7 cm) Cleat* C A 1/2" x 2" (1.3 x 5.1 cm1/2)" x 2" (1.3 x 5.1 cm) DB Spacer (entire deptShpacer (entire depth e C of cutout) D 11/16" (1o.7f ccumto) ut) Side Cleat* 11/16" (1.7 cm) Side GCleat* 11/16" (1.7 cm) Side Cleat* 1/2" x 2" (1.3 x 5.1 cm) 11/S16p"a(c1e.7r (cemn)tire depth SiodfecCulteoautt*) 1/2" x 2" (1.3 x 5.1 cm) Spacer (entire depth of cutout) U(wNitDPhowEoeRur StuCpcpOloy LoUockaNttiooTnpEPoRiwneIsrNtSuapSlplTleyAdLocLaatLiboAnoTvIeO) NG e e G G J KF L M F SIDE VIEW MODEL # JJW2427D in cm A Width of flush inset cutout (min.) 271⁄4 69.2 B Width of opening (min.) 257⁄8 65.7 C Height of flush inset cutout (min.) 307⁄16 77.3 D Height of opening (min.) 2911⁄16 75.4 E Bottom of cutout to floor 45⁄8- 11.732 81.3 F Depth of cutout (min.) 253⁄8E 64.4 G Bottom of cutout to floor for under counter installation F 41⁄16 G10.3 e Recommended junction box location H ELECTRICAL REQUIREMENTS 240 volt, 20-amp fused, grounded circuit is required. A dedicated circuit is required. The length of conduit provided is for serviceability. Do not cut the conduit. The junction box should be located 3" (7.6 cm) maximum below the support surface. Drill a 1" (3.4 cm) minimum F diameter Ahole in tthe right rear or left rear corner of the support surface for access to the junction box. NOTE: For under counter installation, the junction box should be located in the adjacent right or left cabinet. Drill a 1" (2.5 cm) F minimum diameter hole in an upper corner of the side wall for access to the junction box. FLUSH INSTALLATION REQUIREBMENTS A 253⁄8" (64.4 cm) minimum cutout depth is required. These dimensions will result in a 1⁄4" (0.6 cm) reveal on the top, a 1⁄4" (0.6 cm) reveal on the sides and a 1⁄8" (0.3 cm) reveal on the bottom of the wall oven. The front face of the cleats and spacers will be visible and should be treated as a finished surface. CABINET REQUIREMENTS NOTE: When using under counter installation, check cabinet manufacturer's specifications to verify fit. BC F D E Side Cleat* SideSiCdleeaCtle*at* Side Cleat* G13/8" (3.5 cm) 13/8" (3.5 cm) Side Cleat* Side CleaFt* F 13/8" (3.5 cm) Side Cleat* Side Cleat* 13/8" (3.5 cm) TOP VIEW F Power Supply Location F BACK VIEW *Cleats and spacers must be recessed 13⁄8 (3.5 cm) from the front of the cabinet. Power Supply Location IMPORTANT: Dimensional specifications are provided for planning purposes only. Do not mPowaerkSueppaly nLocyaticonutouts based on this information. Refer to the Installation Guide before selecting cabinetry, verifying electrical/gas connections, making cutouts or beginning installation. All Jenn-Air® appliances are appropriately UL, CUL or CSA approved. 8330AdZw615 C D