Jenn-Air JJW2430DS Dimension Guide - Page 3

Front View, Side View, Under Counter Installation, Back View

Get Jenn-Air JJW2430DS PDF manuals and user guides View all Jenn-Air JJW2430DS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 3 highlights

JENN-AIR® DETAILED PLANNING DIMENSIONS 30" SINGLE WALL OVENS JJW3430D, JJW2430D - 30" x 297⁄8" x 255⁄16" 3 of 5 OPENING/CLEARANCE DIMENSIONS A A A D D C* C* D B B C* BE E G e e e Ae E e e F F B F FRONT VIEW A AI SIDE VIEW I e e A e Ie MODEL # JJW3430D JJW2430D in cm A Width of cabinet (min.) 30 76.2 B Width of cutout 281⁄2 72.4 C* Height of cutout (recommended) 28 71.2 D Top of cutout to bottom of upper cabinet door (min.) 23⁄16 5.5 E Bottom of cutout to top of lower cabinet door (min.) 11⁄2 3.8 F Bottom of cutout to floor 32 81.3 E F G Depth of cutout (min.) 24 61.0 G HH Top of countertop to bottom of cutout (min.) 303⁄16 76.7 I Top of cutout to underside of countertop (min.) 11⁄2 3.8 J Bottom of cutout to floor 45⁄16 11.0 e Recommended junction box location G *Will fit cutoutCheDight from 2615⁄16" (68.4 cm) to 297⁄16" (74.8 cm). ELECTRICAL REQUIREMENTS 240 volt, 20-amp fused, grounded circuit is required. A dedicated G circuit is required. The length of conduit provided is for serviceability. Do not cut the conduit. The junction box should be located 3" (7.6 cm) maximum below the support surface. Drill a 1" (2.5 cm) minimum diameter hole in the right rear or left rear corner of the support surface for access to the junction box. NOTE: For under counter installation, the junction box should be located in the adjacent right or left cabinet. Drill a 1" (2.5 cm) minimum diameter hole in an upper corner of the side wall for access to the junction box. CABINET REQUIREMENTS NOTE: When using under counter installation, check cabinet manufacturer's specifications to verify fit. C* C* H H e B B e C* H Power Supply Location g g gB Jg J g g J UNDER COUNTER INSTALLATION (without cooktop installed above) BACK VIEW IMPORTANT: Dimensional specifications are provided for planning purposes only. Do not make any cutouts based on this information. Refer to the Installation Guide before selecting cabinetry, verifying electrical/gas connections, making cutouts or beginning installation. All Jenn-Air® appliances are appropriately UL, CUL or CSA approved. 8331AdZw615

  • 1
  • 2
  • 3
  • 4
  • 5
JENN-AIR
®
DETAILED PLANNING DIMENSIONS
3 of 5
8331AdZw615
IMPORTANT:
Dimensional specifications are provided for planning purposes only.
Do not make any cutouts based on this information.
Refer to the Installation Guide
before
selecting cabinetry, verifying electrical/gas connections, making cutouts or beginning installation.
All Jenn-Air
®
appliances are appropriately UL, CUL or CSA approved.
Power Supply Location
A
B
C*
e
e
E
D
F
G
g
g
B
C*
e
e
J
A
I
H
OPENING/CLEARANCE DIMENSIONS
FRONT VIEW
SIDE VIEW
UNDER COUNTER INSTALLATION
(without cooktop installed above)
BACK VIEW
30" SINGLE WALL OVENS
JJW3430D, JJW2430D – 30" x 29
7
⁄
8
" x 25
5
⁄
16
"
MODEL #
JJW3430D
JJW2430D
in
cm
A
Width of cabinet (min.)
30
76.2
B
Width of cutout
28
1
⁄
2
72.4
C*
Height of cutout
(recommended)
28
71.2
D
Top of cutout to bottom
of upper cabinet door (min.)
2
3
⁄
16
5.5
E
Bottom of cutout to top
of lower cabinet door (min.)
1
1
⁄
2
3.8
F
Bottom of cutout to floor
32
81.3
G
Depth of cutout (min.)
24
61.0
H
Top of countertop to bottom
of cutout (min.)
30
3
⁄
16
76.7
I
Top of cutout to underside of
countertop (min.)
1
1
⁄
2
3.8
J
Bottom of cutout to floor
4
5
⁄
16
11.0
e
Recommended junction box location
*Will fit cutout height from 26
15
⁄
16
" (68.4 cm) to 29
7
⁄
16
" (74.8 cm).
ELECTRICAL REQUIREMENTS
240 volt, 20-amp fused, grounded circuit is required. A dedicated
circuit is required.
The length of conduit provided is for serviceability. Do not cut
the conduit. The junction box should be located 3" (7.6 cm)
maximum below the support surface. Drill a 1" (2.5 cm)
minimum diameter hole in the right rear or left rear corner of
the support surface for access to the junction box.
NOTE:
For under counter installation, the junction box should be
located in the adjacent right or left cabinet. Drill a 1" (2.5 cm)
minimum diameter hole in an upper corner of the side wall for
access to the junction box.
CABINET REQUIREMENTS
NOTE:
When using under counter installation, check cabinet
manufacturer’s specifications to verify fit.