Jenn-Air JJW2430DS Dimension Guide - Page 4

JENN-AIR® DETAILED PLANNING DIMENSIONS 30" SINGLE WALL OVENS - FLUSH INSTALLATION JJW3430D, JJW2430D - 30" x 297⁄8" x 245⁄16" (depth without handle) 4 of 5 OPENING/CLEARANCE DIMENSIONS 3/4" (1.9 cm) Top Cleat* 3/4" (1.9 cm) Top Cleat* A A B B C D 11/16" (1.7 cm) C 3/4" (1.9 cm) Top Cleat* D A B 3/4" (1.9 cm) 111/11/61"6"(1(1.7.7ccTmmo)p) Cleat1*1/16" (1.7 cm) Side Cleat* 1/2" x 2" (1.3CSSixdiAde5e.C1DClBecl1ema/a2t")t**x 2" Side Cleat* (1.3 x 5.1 cm) Spacer (entire deptShpacer (entire depth C of cutout) 11/16" (1o.7f ccumto) ut) 11/16" (1.7 cm) D Side Cleat* Side Cleat* e e 11/16" (1.7 cm) 11/1S16/p"2"a(1xce.e27r"c((em1n.)3tirxe 5.1 cm) depth e Side Cleat* Sidoef cCuletoaut*t) 1/2" x 2" (1.3 x 5.1 cm) Sopf aceucetor u(et)ntire depth E eE e e E E FRONT VIEW e e 3/4" (1.9 cm) 3/4" (1.9 cm) e Top Cleat* Top Cleeat* A A B B C eD C D 3/4" (1.9 cm) Top Cleat* A 11/16" (1.7 cm) Side Cleat* B 111/11/61"6"(1(1.7.7cc3m/m4)")(1.9 cm11/)16" (1.7 cm) SSidideeCCleleaatt*T*op CleatS*ide Cleat* e 1/2" x 2" Spacer ((e1n.3CtirxeA5d.e1DpBctS1mh/p2")axce2r" (1.3 x (entire 5.1 cm) depth C of cutout) 11/16" (1o.7f ccumto) ut) D Side Cleat* 11/16" (1.7 cm) Side GCleat* 11/16" (1.7 cm) Side Cleat* 1/2" x 2" (1.3 x 5.1 cm) 11/1S6p" a(1c.e7r c(emn)tire depth Sidoef cCuletoaut*t) 1/2" x 2" (1.3 x 5.1 cm) Spacer (entire depth of cutout) U(wNitDPhowEoeRur StuCpcpOloy LoUockaNttiooTnpEPoRwinerIsSNtuapSplllyTeLAdocLaatLiobnAoTvIeO) NG e e G G F F SIDE VIEW MODEL # JJW3430D JJW2430D in cm A Width of flush inset cutout (min.) 301⁄4 76.8 B Width of opening (min.) 287⁄8 73.3 C Height of flush inset cutout (min.) 307⁄16 77.3 D Height of opening (min.) 2911⁄16 75.4 E Bottom of cutout to floor 45⁄8- 11.732 81.3 F Depth of cutout (min.) E 253⁄8 G Bottom of cutout to floor for under counter F 4G1⁄16H e Recommended junction box location 64.4 10.3 ELECTRICAL REQUIREMENTS 240 volt, 20-amp fused, grounded circuit is required. A dedicated circuit is required. The length of conduit provided is for serviceability. Do not cut F the conduit. The junction box should be located 3" (7.6 cm) maximum below the support surface. Drill a 1" (2.5 cm) C D mA inimum diameter hole in the right rear or left rear corner of the support surface for access to the junction box. F NOTE: For under counter installation, the junction box should be located in the adjacent right or left cabinet. Drill a 1" (2.5 cm) minimum diameter hole in an upper corner of the side wall for access to the junction box. FLUSH INSTALLATION RBEQUIREMENTS A 253⁄8" (64.4 cm) minimum cutout depth is required. These dimensions will result in a 1⁄4" (0.6 cm) reveal on the top, a 1⁄4" (0.6 cm) reveal on the sides and a 1⁄8" (0.3 cm) reveal on the bottom of the wall oven. The front face of the cleats and spacers will be visible and should be treated as a finished surface. CABINET REQUIREMENTS NOTE: When using under counter installation, check cabinet manufacturer's specifications to verify fit. F Side Cleat* SidSeidCeleCalte*at* Side Cleat* 13/8" (3.5 cm) 13/8" (3.5 cm) Side Cleat* Side CleaFt* 13/8" (3.5 cm) Side Cleat* Side Cleat* 13/8" (3.5 cm) TOP VIEW F Power Supply Location F BACK VIEW * Cleats and spacers must be recessed 13⁄8" (3.5 cm) from the front of the cabinet. Power Supply Location IMPORTANT: Dimensional specifications are provided for planning purposes only. Do not Pmowear kSuepplyaLnocyatiocnutouts based on this information. Refer to the Installation Guide before selecting cabinetry, verifying electrical/gas connections, making cutouts or beginning installation. All Jenn-Air® appliances are appropriately UL, CUL or CSA approved. 8331AdZw615