Jenn-Air JJW6024HM Dimension Guide - Page 4
Jennair, Small Steam Oven - Flush Installation
View all Jenn-Air JJW6024HM manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 4 highlights
DETAILED PLANNING DIMENSIONS 4 of 8 JENNAIR® SMALL STEAM OVEN - FLUSH INSTALLATION JJW6024HM - 237⁄16" X 185⁄16" X 203⁄8" (Depth Without Handle) JJW6024HL - 237⁄16" X 185⁄16" X 203⁄8" (Depth Without Handle) OPENING/CLEARANCE DIMENSIONS 1/4" (0.6 cm) Top Cleat* A B C D 3/4" x 1" (1.9 x 2.5 cm) width x min. thickness Side Cleat* 3" x 1/2" (7.6 cm x 1.3 cm) or 3" x 5/16" (7.6 cm x 0.8 cm) without bottom trim Width x Height Spacer (entire depth of cutout) e e E FRONT VIEW SIDE VIEW 1/4" (0.6 cm) Top Cleat* e A e B C D 3/4" x 1" (1.9 x 2.5 cm) width x min. thickness Side Cleat* 3" x 1/2" (7.6 cm X 1.3 cm) or 3" x 5/16" (7.6 cm x 0.8 cm) without bottom trim Width X Height Spacer (entire depth of cutout) MODEL # JJW6024HM JJW6024HL in cm A Width of flush inset cutout (min.) 2311⁄16 60.2 B Width of opening (min.) 22 55.9 C Height of flush inset cutout (min.) 189⁄16 47.2 D Height of opening (min.) 183⁄8 46.6 E Depth of cutout (min.) 203⁄8 51.8 e Recommended junction box location ELECTRICAL REQUIREMENTS 120 V, 15 A fused, grounded circuit is required. A dedicated circuit is required. The length of conduit provided is for serviceability. Do not cut the conduit. The junction box should be located 3" (7.6 cm) maximum below the support surface. Drill a 1" (3.4 cm) minimum diameter hole in the right rear or left rear corner of the support surface for access to the junction box. NOTE: For under counter installation, the junction box should be located in the adjacent right or left cabinet. Drill a 1" (2.5 cm) minimum diameter hole in an upper corner of the side wall for access to the junction box. FLUSH INSTALLATION REQUIREMENTS A 207⁄16" (51.8 cm) minimum cutout depth is required. These dimensions will result in a 1/8" (0.3 cm) reveal on the top, a 1/8" (0.3 cm) reveal on the sides and a 1/8" (0.3 cm) reveal on the bottom of the wall oven. The front face of the cleats and spacers will be visible and should be treated as a finished surface. CABINET REQUIREMENTS NOTE: When using under counter installation, check cabinet manufacturer's specifications to verify fit. Power Supply Location E Side Cleat* Side Cleat* JJW6024HM: 13/16" (20.5 mm) JJW6024HL: 7/8" (21.3 mm) UNDER COUNTER INSTALLATION (without cooktop installed above) TOP VIEW *Cleats and spacers must be recessed 13/16" (2.1 cm) from the front of the cabinet. IMPORTANT: Dimensional specifications are provided for planning purposes only. Do not make any cutouts based on this information. Refer to the Installation Guide before selecting cabinetry, verifying electrical/gas connections, making cutouts or beginning installation. All JennAir® appliances are appropriately UL, CUL or CSA approved. BACK VIEW W11318374C Installation Instructions: W11260095