Jenn-Air JUR248RWES Use and Care - Page 6

Install Custom Overlay Panel - jenn aire

Get Jenn-Air JUR248RWES PDF manuals and user guides View all Jenn-Air JUR248RWES manuals
Add to My Manuals
Save this manual to your list of manuals

Page 6 highlights

Clean Before Using After you remove all of the package materials, clean the inside of your refrigerator before using it. See the cleaning instructions in "Refrigerator Care." 3. Open the door. Lift the front of the door up, pulling straight out to remove as shown. Important information to know about glass shelves and covers: Do not clean glass shelves or covers with warm water when they are cold. Shelves and covers may break if exposed to sudden temperature changes or impact, such as bumping. Tempered glass is designed to shatter into many small, pebble-size pieces. This is normal. Glass shelves and covers are heavy. Use both hands when removing them to avoid dropping. Install Custom Overlay Panel IMPORTANT: ■ Create custom overlay panel according to the specifications in the "Custom Overlay Panel" section. ■ Jenn-Air is not responsible for the removal or addition of molding or decorative panels that would not allow access to the refrigerator for service. Remove the Door IMPORTANT: Do not remove the grease from the washer, top spacer or top hinge pin. Be sure to set aside the top hinge, top spacer and washer for later use. 1. Using a Phillips screwdriver, remove the three screws from the top hinge. Remove the top hinge. Attach the Overlay Panel NOTE: If the overlay hooks are not installed, see "Custom Overlay Panel" for overlay hook locations. 1. Position the overlay panel ¹⁄₂" (1.27 cm) higher than the door. Be sure to position the overlay hooks to the pilot holes. A B C 2. Insert the overlay hooks into the top of the holes in the door. D Push against the overlay panel to force the overlay hooks deeper into the door. Pull the overlay panel straight down to secure the overlay hooks to the door. 3. Using a Phillips screwdriver, attach the overlay plates to the E bottom of the overlay panel and door as shown. A. Screws (3) B. Top hinge C. Washer D. Top spacer E. Door 2. Remove the three screws from the top spacer. Remove the top spacer and washer. A B C D A. Overlay panel B. Door C. Overlay plates (2) D. Round-head screws (8) 6

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
6
Clean Before Using
After you remove all of the package materials, clean the inside of
your refrigerator before using it. See the cleaning instructions in
“Refrigerator Care.”
Install Custom Overlay Panel
IMPORTANT:
■
Create custom overlay panel according to the specifications in
the “Custom Overlay Panel” section.
■
Jenn-Air is not responsible for the removal or addition of
molding or decorative panels that would not allow access to
the refrigerator for service.
Remove the Door
IMPORTANT:
Do not remove the grease from the washer, top
spacer or top hinge pin. Be sure to set aside the top hinge, top
spacer and washer for later use.
1.
Using a Phillips screwdriver, remove the three screws from the
top hinge. Remove the top hinge.
2.
Remove the three screws from the top spacer. Remove the
top spacer and washer.
3.
Open the door. Lift the front of the door up, pulling straight out
to remove as shown.
Attach the Overlay Panel
NOTE:
If the overlay hooks are not installed, see “Custom Overlay
Panel” for overlay hook locations.
1.
Position the overlay panel
¹⁄₂
" (1.27 cm) higher than the door.
Be sure to position the overlay hooks to the pilot holes.
2.
Insert the overlay hooks into the top of the holes in the door.
Push against the overlay panel to force the overlay hooks
deeper into the door. Pull the overlay panel straight down to
secure the overlay hooks to the door.
3.
Using a Phillips screwdriver, attach the overlay plates to the
bottom of the overlay panel and door as shown.
A. Screws (3)
B. Top hinge
C. Washer
D. Top spacer
E. Door
Important information to know about glass shelves
and covers:
Do not clean glass shelves or covers with warm water when
they are cold. Shelves and covers may break if exposed to
sudden temperature changes or impact, such as bumping.
Tempered glass is designed to shatter into many small,
pebble-size pieces. This is normal. Glass shelves and covers
are heavy. Use both hands when removing them to avoid
dropping.
C
D
E
A
B
A. Overlay panel
B. Door
C. Overlay plates (2)
D. Round-head screws (8)
A
C
D
B