Jenn-Air JWD3027EX Dimension Guide - Page 4

Warming Drawers - Flush Installation

Get Jenn-Air JWD3027EX PDF manuals and user guides View all Jenn-Air JWD3027EX manuals
Add to My Manuals
Save this manual to your list of manuals

Page 4 highlights

JENN-AIR® DETAILED PLANNING DIMENSIONS 30"/27" WARMING DRAWERS - FLUSH INSTALLATION JWD3030E - 293⁄4" x 101⁄4" x 241⁄2" (depth without handle) JWD3027E - 263⁄4" x 101⁄4" x 241⁄2" (depth without handle) 4 of 4 OPENING/CLEARANCE DIMENSIONS MODEL # A Width of flush inset cutout (min.) B Width of opening (min.) C Height between cutouts (min.) D Height of opening (min.) E Height of flush inset cutout (min.) Bottom of cutout to floor (recommended) F Bottom of cutout to floor (min.) G Depth of cutout (min.) e Recommended outlet location JWD3030E in cm 301⁄4 76.8 281⁄4 71.8 21⁄2 6.4 91⁄8 23.2 103⁄4 27.3 81⁄4 21.0 5 12.7 25 63.5 JWD3027E in cm 271⁄4 69.2 251⁄4 64.1 21⁄2 6.4 91⁄8 23.2 103⁄4 27.3 81⁄4 21.0 5 12.7 25 63.5 ELECTRICAL REQUIREMENTS 120 volt, 60 Hz, AC only, 15-amp fused, electrical circuit is required. A dedicated circuit is recommended. If the outlet is on the rear wall behind the warming drawer, it must be recessed and located in A A B the upper right-hand corner. If outlet is located in an adjacent cabinet, drill a 13⁄8" (3.5 cm) minimum diameter hole in the side wall or support surface to access the pBoawckeorf sCuapbipnleyt cord. Back of Cabinet B 1" (2.5 cmC) C LOCATION REQUIREMENTS D D E 7/8" (2.2 cm) 1Si"d(e2.C5lecamP7/tl8)sa"*t(f2o.r2mec*m) Side Cleats* e E Support surface must be solid, level and flush with the bottom of the cabinet cutout. The warming drawer must be leveled before completing installation. Platform* FLUSH INSTALLATION REQUIREMENTS G A 25" (63.5 cm) minimum cutouGt depth is required. These dimensions will result in a 1⁄4" (0.6 cm) reveal on all sides of the warming drawer. F The front face of the cleats and platforms will be visible and should be treated as a finished surface. F FRONT VIEW Back of Cabinet A A G B SIDEBVIEW C C Power Cord Location BACK VIEW G G Side Cleat* 15/8" (4.1 cm) Side Cleat* Side Cleat* 15/8" (4.1 cm) Side Cleat* TOP VIEW *Cleats and platform must be recessed 15⁄8" (4.1 cm) from the front of the cabinet. IMPORTANT: Dimensional specifications are provided for planning purposes only. Do not make any cutouts based on this information. Refer to the Installation Guide before selecting cabinetry, verifying electrical/gas connections, making cutouts or beginning installation. All Jenn-Air® appliances are appropGriately UL, CUL or CSA approved. 8689AdZw1216

  • 1
  • 2
  • 3
  • 4
JENN-AIR
®
DETAILED PLANNING DIMENSIONS
4 of 4
IMPORTANT:
Dimensional specifications are provided for planning purposes only.
Do not make any cutouts based on this information.
Refer to the Installation Guide
before
selecting cabinetry, verifying electrical/gas connections, making cutouts or beginning installation.
All Jenn-Air
®
appliances are appropriately UL, CUL or CSA approved.
8689AdZw1216
G
Side Cleat*
1
5
/
8
" (4.1 cm)
Side Cleat*
Power Cord Location
e
A
E
F
C
B
1" (2.5 cm)
Side Cleats*
7
/
8
" (2.2 cm)
Platform*
D
Back of Cabinet
G
OPENING/CLEARANCE DIMENSIONS
FRONT VIEW
SIDE VIEW
BACK VIEW
30"/27" WARMING DRAWERS – FLUSH INSTALLATION
JWD3030E – 29
3
⁄
4
" x 10
1
⁄
4
" x 24
1
⁄
2
"
(depth without handle)
JWD3027E – 26
3
⁄
4
" x 10
1
⁄
4
" x 24
1
⁄
2
"
(depth without handle)
MODEL #
JWD3030E
JWD3027E
in
cm
in
cm
A
Width of flush inset cutout (min.)
30
1
⁄
4
76.8
27
1
⁄
4
69.2
B
Width of opening (min.)
28
1
⁄
4
71.8
25
1
⁄
4
64.1
C
Height between cutouts (min.)
2
1
⁄
2
6.4
2
1
⁄
2
6.4
D
Height of opening (min.)
9
1
⁄
8
23.2
9
1
⁄
8
23.2
E
Height of flush inset cutout (min.)
10
3
⁄
4
27.3
10
3
⁄
4
27.3
F
Bottom of cutout to floor (recommended)
8
1
⁄
4
21.0
8
1
⁄
4
21.0
Bottom of cutout to floor (min.)
5
12.7
5
12.7
G
Depth of cutout (min.)
25
63.5
25
63.5
e
Recommended outlet location
ELECTRICAL REQUIREMENTS
120 volt, 60 Hz, AC only, 15-amp fused, electrical circuit is required. A dedicated circuit
is recommended.
If the outlet is on the rear wall behind the warming drawer, it must be recessed and located in
the upper right-hand corner. If outlet is located in an adjacent cabinet, drill a 1
3
⁄
8
" (3.5 cm)
minimum diameter hole in the side wall or support surface to access the power supply cord.
LOCATION REQUIREMENTS
Support surface must be solid, level and flush with the bottom of the cabinet cutout.
The warming drawer must be leveled before completing installation.
FLUSH INSTALLATION REQUIREMENTS
A 25" (63.5 cm) minimum cutout depth is required.
These dimensions will result in a
1
⁄
4
" (0.6 cm) reveal on all sides of the warming drawer.
The front face of the cleats and platforms will be visible and should be treated as a finished surface.
TOP VIEW
*Cleats and platform must be recessed 1
5
⁄
8
" (4.1 cm)
from the front of the cabinet.