Jenn-Air JXW5036WS Installation Instruction - Page 11

Range Hood Use - cooktops

Get Jenn-Air JXW5036WS PDF manuals and user guides View all Jenn-Air JXW5036WS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

Install Filters 1. For non-vented (recirculating installations) install charcoal filter, wrapping it around the grease filter. 2. Place the charcoal filter mat around the grease filter and fix it in place by using the cap lock springs provided. 3. Position the upper cap and fix it in place using the cap lock spring provided. RANGE HOOD USE The range hood is designed to remove smoke, cooking vapors and odors from the cooktop area. For best results, start the hood before cooking and allow it to operate several minutes after the cooking is complete to clear all smoke and odors from the kitchen. Control Panel The range hood controls are located on the front side of the canopy. AB C DE A. Charcoal filter mat B. Grease filter C. Charcoal filter side lock springs D. Upper cap E. Cap lock spring F. Grease filter support 4. For all installations, install the grease filter. See "Range Hood Care" section. Complete Installation Check Range Hood Operation If range hood does not operate, check to see whether a circuit breaker has tripped or a household fuse has blown. NOTE: To get the most efficient use from your new range hood, read the "Range Hood Use" section. A. Power decrease B. Power increase C. Display D. Light E. Timer Display Grease Filter Saturation Alarm After 30 hours of fan function, the display will show "Clean Grease Filter" when the fan is active. When this icon shows in the display, the installed grease filters should be washed. See "Range Hood Care" section. ■ To reset the grease filter saturation alarm, press and hold the POWER INCREASE button for 5 seconds. The "Clean Grease Filter" icon will no longer be displayed. Charcoal Filter Saturation Alarm After 120 hours of fan function, the display will show "Replace Charcoal Filter" when the fan is active. When this icon shows in the display, the charcoal filters should be replaced. See "Range Hood Care" section. ■ To reset the charcoal filter saturation alarm, press and hold the POWER DECREASE button for 5 seconds. The "Replace Charcoal Filter" icon will no longer be displayed. 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
11
Install Filters
1.
For non-vented (recirculating installations) install charcoal
filter, wrapping it around the grease filter.
2.
Place the charcoal filter mat around the grease filter and fix it
in place by using the cap lock springs provided.
3.
Position the upper cap and fix it in place using the cap lock
spring provided.
4.
For all installations, install the grease filter. See “Range Hood
Care” section.
Complete Installation
Check Range Hood Operation
If range hood does not operate, check to see whether a circuit
breaker has tripped or a household fuse has blown.
NOTE:
To get the most efficient use from your new range hood,
read the “Range Hood Use” section.
RANGE HOOD USE
The range hood is designed to remove smoke, cooking vapors
and odors from the cooktop area. For best results, start the hood
before cooking and allow it to operate several minutes after the
cooking is complete to clear all smoke and odors from the
kitchen.
Control Panel
The range hood controls are located on the front side of the
canopy.
Display
Grease Filter Saturation Alarm
After 30 hours of fan function, the display will show “Clean
Grease Filter” when the fan is active. When this icon shows in the
display, the installed grease filters should be washed. See
“Range Hood Care” section.
■
To reset the grease filter saturation alarm, press and hold the
POWER INCREASE button for 5 seconds. The “Clean Grease
Filter” icon will no longer be displayed.
Charcoal Filter Saturation Alarm
After 120 hours of fan function, the display will show “Replace
Charcoal Filter” when the fan is active. When this icon shows in
the display, the charcoal filters should be replaced. See “Range
Hood Care” section.
■
To reset the charcoal filter saturation alarm, press and hold
the POWER DECREASE button for 5 seconds. The “Replace
Charcoal Filter” icon will no longer be displayed.
A. Charcoal filter mat
B. Grease filter
C. Charcoal filter side lock springs
D. Upper cap
E. Cap lock spring
F. Grease filter support
A. Power decrease
B. Power increase
C. Display
D. Light
E. Timer
A
B
C
D
E