Karcher B 110 R Bp Pack 170AhDoseSSDR75 Operating instructions 1 - Page 23

1 Battery plug, device side 2 Battery plug, battery side 3. Connect the battery-side battery connector to the charger. 4. Plug the mains plug of the charger into the socket. 5. Carry out the charging process in accordance with the operating instructions for the charger. 6. Connect the device-side battery connector to the battery-side battery connector. 7. Pivot the waste water tank forwards and close it. Internal charger 1. Unlock the waste water tank and pivot it up. 2. Plug the mains plug of the internal charger into the mains socket. The charging state of the battery is shown on the control panel display. 3. Unplug the charger mains plug from the mains socket after charging. 4. Pivot the waste water tank forwards. Low-maintenance batteries (wet batteries) ƽ DANGER Refilling discharged batteries with water Danger of acid burns from escaping acid, destruction of clothing Wear safety goggles, protective clothing and protective gloves when handling the battery acid. Observe the applicable regulations. Immediately rinse off any splashed acid from the skin or clothing using copious amounts of water. ATTENTION Using water with additives Defective batteries, loss of warranty eligibility Top up the batteries using only distilled or desalinated water (EN 50272-T3). Do not use any foreign additives, so-called enhancing agents, because this will invalidate the warranty. 1. Add distilled water one hour before the charging process comes to an end. Observe the correct acid level according to the battery label. All cells must produce gas at the end of the charging process. 2. Clean up any spilled water. To do this, proceed as described in the Care and maintenance chapter in the "Cleaning the batteries" section. Operation ƽ DANGER Falling objects Risk of injury Do not drive the device into areas where there is a possibility of the operating personnel being hit by falling objects. ATTENTION Risks during operation Risk of injury In the event of danger, set the safety switch to "0". Pushing the device To push the device, the brake must be unlocked. ƽ DANGER Danger of accident When the brake is unlocked, the function of the brake is permanently out of operation. Be sure to remove the coins for unlocking immediately after the sliding process has ended. 1. Swing the unlocking lever away from the wheel and hold it there. 1 Unlocking lever 2. Insert a coin between the casing and the lever at both ends of the lever. 3. Release the unlocking lever. 4. Push the device. 5. Remove both coins immediately after pushing. Adjusting the seat Adjusting the height 1. Stand next to the device. 2. Raise the seat at the back. 3. Align the front seat bracket to the desired height of the device. 4. Lower the seat at the back. Adjusting the position 1. Operate the seat adjustment lever and move the seat to the desired position. 2. Release the seat adjustment lever and latch the seat into position. Switching the device on 1. Sit in the driver's seat. 2. Insert the Intelligent Key. 3. Set the safety switch to "1". 4. Turn the program switch to the desired function. 5. If one of the displays below appears on the display, take your foot off the accelerator pedal, set the safety switch to "0" and carry out the necessary maintenance work. Display Activity maintenance Clean the suction bar. squeegee maintenance Check the brushes for brush head wear and clean them. maintenance Check the suction lips for squeegee wear and correct adjust- blade ment. maintenance Clean the fluff filter. turbine filter maintenance Clean the fresh water filter. fresh water filter 6. Press the Info button. 7. Reset the counter for the corresponding maintenance (see "Grey Intelligent Key / Reset maintenance counter"). Note If the counter is not reset, the maintenance display appears again each time the device is switched on. Switching on the light Daytime running light The daytime running light is in operation when the device is switched on. Sidelight The sidelight lights up as soon as the program switch is set to a cleaning program. Checking the parking brake ƽ DANGER Defective parking brake Danger of accident Before each operation, check the function of the parking brake on level ground. 1. Switch the device on. 2. Set the travel direction switch to "For- ward". 3. Set the program selector switch to "TRANSPORT MODE". 4. Press the accelerator pedal lightly. The brake must audibly unlock. The appliance must roll easily on a plane surface. 5. Release the accelerator pedal. The brake must be audibly engage. If this is not the case, take the device out of operation and call Customer Service. Driving ƽ DANGER Lack of braking Danger of accident Before using the device, it is essential to check the function of the parking brake. Never use the device if the parking brake does not work. ƽ DANGER Careless driving Danger of tipping over Only drive up and up gradients in the direction of travel and across the direction of travel 10%. Do not turn up or down gradients. Drive slowly in corners and on wet ground. Only drive the device on stable ground. English 23