Kenmore 28615 Owners Manual - Page 18

Light, Changing

Get Kenmore 28615 - Canister Vacuum PDF manuals and user guides View all Kenmore 28615 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

TO REPLACE BELT !. install new belt over motor drive, then over belt path° NOTE: See PARTS AND FEATURES for Belt humhero Agitator Motor Drive End Cap Path 2, Place agitator assembly back into PowerMate. 3. Line up front of cover and base, Rest cover on front edge of base as shown. Cover Base Side Latch i {__._ _ Rear Latches 4, Rotate cover back,, Press cover firmly until side and rear latches snap into place, Make sure there is no gap between the cover and base° 5. Turn PowerMate upside down and replace two (2) cover screws, I LIGHT BULB CHANGING 1 1. Remove PowerMate cover as shown in BELT CHANGING AND AGITATOR CLEANING section, 2. Push in and turn bulb counterclockwise, then pull out to remove,, --'-'_Push in l! ._,/-A&n,d_'_T:_u_rn_ L-_ 3. Push in and turn breuplblaccelo, ckwBiusleb, mtuost 15 Watts( 130 Volts)° not be higher than 4. Reinstall PowerMate cover as shown in BELT CHANGING AND AGITATOR CLEANING section, NOTE: See PARTS AND FEATURES for bulb number,, 18

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
TO
REPLACE
BELT
!.
install
new
belt over
motor
drive,
then over
belt path°
NOTE:
See
PARTS
AND
FEATURES
for Belt hum-
hero
Agitator
End
Cap
Motor
Drive
Path
2, Place agitator
assembly
back into
PowerMate.
3. Line up
front
of
cover
and
base,
Rest
cover
on
front
edge
of base as
shown.
Side
Latch
Cover
Base
4, Rotate
cover
i
{_-
back,, Press
_._
cover firmly
until
_
side
and
rear
latches
snap
Rear
into place,
Latches
Make sure there is no gap between the
cover and base°
5.
Turn
PowerMate
upside
down and
replace
two (2) cover
screws,
I
LIGHT
BULB
CHANGING
1. Remove
PowerMate
cover as shown
in
BELT CHANGING
AND
AGITATOR
CLEANING
section,
2.
Push in and turn
bulb counterclock-
wise,
then pull out
to remove,,
--'-'_Push
in
l!
3.
Push in and turn
And
Turn
L-_
bulb clockwise,
to
._,/-&,_'_:___
replace,
Bulb must
not be higher
than
15 Watts( 130 Volts)°
4. Reinstall
PowerMate
cover
as shown
in
BELT CHANGING
AND
AGITATOR
CLEANING
section,
NOTE:
See PARTS AND
FEATURES
for
bulb number,,
1
18