Kenmore 6817 Installation Instructions

TO

BE REMOVED

BYTHE

CUSTOMER

AFTER

iNSTALLATiON

IS

COMPLETE

f

[]

iNSTALLATION

CHECKOFF

LIST

[]

[]

[]

[]

f

DOORS

[]

Handles are secure and tight

[]

Door seals completely

to cabinet

on all sides

[]

Freezer door is level across the top

Leveling

[]

Refrigerator

is level, side to side and tilted 1/4" (6mm) front to back

[]

Toe grille is properly attached

to refrigerator

[]

Cabinet is setting solid on all corners

Electrical

Power

[]

House

power turned on

[]

Refrigerator

plugged

in

ice

Maker

[]

House water supply

connected

to refrigerator

[]

No water leaks present

at all connections

- recheck

in 24 hours

[]

Ice Maker is turned

ON.

Final

Checks

Shipping

material

removed

Fresh Food and Freezer controls

set

Crisper

Humidity

controls

set

Registration

Card sent in

Tools Necessary:

Phillips"

head

Quodrex

hood

screwdriver

1

%

f

2

Socket

Wrench

Set

Adjustable

Wrench

HAND

TRUCKING

,,

Load refrigerator

from side of cabinet

only.

,,

Do not run retaining

straps over handles.

,,

Do not over-tighten

retaining

straps.

,,

Never use refrigerator

handles

to move the

refrigerator.

,,

Remove tape from

doors only after unit is in

place.

1

Piece

of Ta#e

2 Pieces of Tape

--

2

Piece8

of Tape

.-f"

2 Pieces of T_pe

.........

4 Pieces of TapeJ

Toe Grille

r--"

J

2 Pieces of

Foam

_

SHIPPING

MATERIAL

. !OD

1

.......

fT_l

\

2

Pieces

of

Foam

.........

I

-

1

Piece

ol Tape

1

Piece

of _hpe

"_

2

I:_ieees

of I_pe

......

2

Pieces

of Tape

"\"

2

_:'_eees

of I_pe

"-_2

P_eees

ef Tape

Remove

Shipping

material.

(Features

may

vary

per model.)

3

WATER

SUPPLY

Plastic

Water

Connect water supply - check for water

leaks. Turn

icemaker OFF if

water

supply

is not connected

immediately.

Connecting

to a reverse

osmosis

system

is not recommended.

gliii!iiijli

J

INSTALLATION

CLEARANCES

Allow the following

clearances

for ease of installation,

proper air circulation,

and

plumbing

and electrical

connections:

,,

Sides & Top

..........

3/8"

*

Back

.......................

1"

4

f

-,

LEVELING

AND

ADJUSTING

All four corners

of your refrigerator

must rest firmly on a solid floor. Your refrigerator

is equipped

with adjustable

front rollers or front leveling screws

to help level your

unit.

To level

cabinet or

change

door height:

1. Remove toe grille.

2. Use flat-blade screwdriver or 3/8" socket wrench to adjust front rollers. Use

adjustable wrench to adjust leveling screws.

Toe Grille

Adjustable

Front Roller

(some models)

Stationary

Front Roller

with Leveling Screw

(some models)

Humidity

""H_h'd'ty_-_)_

o

6

CONTROLS

When changing

controls,

wait 24

hours before making

additional

adjustments.

/

7

ICEMAKER

Ensure icemaker

is turned

ON.

[/"/_,//_

Signal

Arm

f

if you need to remove the doors to get your refrigerator

into the house please see "Door Removal and Reversal

instructions"

in your

Use & Care Manual.

DOOR

REMOVAL

(iF

NECESSARY)

Cable

Bottom

ube

,J

Shim

Center

See "Normal

Operating

Sights

& Sounds"

in the

Use & Care Manual

so you understand

the sounds

you may hear once your refrigerator

is

running.

Please read

entire

Use & Care Manual

to become aware of important

safety instructions

and to become familiar witrh your new refrigerator.

Send

in

Registration

card to register your refrigerator.

Congratulations!

You are ready to enjoy your new refrigerator.

OR_

iii

Kenmore 6817 Installation Instructions

Kenmore 6817 - 20.6 cu. Ft. Top Freezer Refrigerator Manual

Kenmore 6817 manual content summary: