Kenmore 9743 Installation Instructions - Page 1

INSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALIFIED INSTALLER. IMPORTANT: SAVE FOR LOCAL ELECTRICAL INSPECTOR'S USE. READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. Clearances and Dimensions 1. Provide adequate clearances between the range and adjacent combustible surfaces. 2. Location--Check location where the range will be installed. Check for proper electrical supply, and the stability of the floor. 3. Dimensions that are shown must be used. Given dimensions provide minimum clearance. Contact surface must be solid and level. RANGE OVERALL DIMENSIONS RANGEELECTRICAL CONNECTIONS FRONT-- TYPICALCABINETINSTALLATION SIDE VIEW 25- 3/4" ....._..-.. 30"--.j._... 4 /2" electricailoutletIocat,o_ _- 30"--_ 30" Minimum Minimumto 1"4_ wall on either side of range _®'® 1[_ _ above 36" height. 18" cabinetson ®'® _/ 't Meiitnhiemrsuimdeto of range. 1_-13"-_ Maximumdepth faobrocvaebrinaentgsetop. [_ i_ i iii "5/8"w* Door Open _ 29-7/8"-'_ _5 \41"" -- - - Fig. 1 _rW Depthis 28-I 3/32"with door handle. Edge 2-5/8"for models equipped withwarmer drawers, 3-1/2"for models equipped withstorage drawers Fig. 2 Fig. :3 ,t_ 30" -_ 0" clearancebelow cookingtop and at rear of range. *30" MINIMUM CLEARANCE BETWEEN THE TOP OF THE COOKING SURFACEAND THE BOTTOM OF AN UNPROTECTED WOOD OR METAL CABI NET; OR 24" MINIMUM WHEN BOTTOM OF WOOD OR METAL CABINET IS PROTECTED BY NOT LESS THAN 1/4" FLAME RETARDANT MILLBOARD COVERED WITH NOT LESS THAN NO. 28 MSG SHEETSTEEL, 0.015" STAINLESS STEEL, 0.024"ALUMINUM OR 0.020" COPPER. 0" CLEARANCE IS THE MINIMUM FOR THE REAR OF THE RANGE. FOLLOW ALL DIMENSION REQUIREMENTS PROVIDED ABOVE TO PREVENT PROPERTY DAMAGE, POTENTIAL FIRE HAZARD, AND INCORRECT COUNTERTOP AND CABINET CUTS. TO ELIMINATE THE RISK OF BU RNS OR FIRE BY REACHING OVER HEATED SU RFACE UNITS, CABINET STORAGE SPACE LOCATED ABOVE THE SURFACE UNITS SHOULD BE AVOIDED. IF CABINET STORAGE IS TO BE PROVIDED, THE RISK CAN BE REDUCED BY INSTALLING A RANGE HOOD THAT PROJECTS HORIZONTALLY A MINIMUM OF 5" BEYOND THE BOTTOM OF THE CABINETS. IMPORTANT SAFETY INSTRUCTIONS Important Note to the Consumer Keep these instructions with your owner'sguide for future reference. • ALL RANGES CAN TIP • INJURYTO PERSONS COULD RESULT • INSTALL ANTI-TIP DEVICE PACKED WITH RANGE • SEE INSTALLATION INSTRUCTIONS _!VAt/-'l=l_ll_[_lIlf the information in this manual is not followed exactly, a fire or electrical shock may result causing property damage, personal injury or death. Important Notes to the Installer Read all instructions contained in these installation instructions before installing range. Remove all packing material from the oven compartments before connecting the gas & electrical supply to the range. Observe all governing codes and ordinances. Be sure to leave these instructions with the consumer. As when using any appliance generating heat, there are certain safety precautions you should follow. These are listed in the Use & Care Guide, read it carefully. Be sure your range is installed and grounded properly by a qualified installer or service technician. Make sure the wall coverings around the range can withstand the heat generated by the range. To eliminate the need to reach over the surface elements, cabinet storage space above the elements should be avoided. Serial Plate Locations: Serial plate location: Serial plate is located on the lower right front frame of the appliance. Alternate location may be under cooktop. 316454912 EspaSol - Paginas 5-8