Kenmore 9743 Installation Instructions - Page 3
Range, Connection, Opening, Chart - review
View all Kenmore 9743 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 3 highlights
2b. MODELS REQUIRING POWER SUPPLY CORD KIT. RISK OF FIRE OR ELECTRICAL SHOCK MAY OCCUR IFAN INCORRECT SIZE RANGE CORD KIT IS USED, THE INSTALLATION INSTRUCTIONS ARE NOT FOLLOWED OR STRAIN RELIEF BRACKETIS DISCARDED. This appliance may be connected by means of a power supply cord. Only a power supply cord kit rated at 125/250 volts minimum, and marked for use with ranges shall be used. See Fig. 10 for cord kit ampere rating information. Cord must have either three (3) or four (4) conductors (See Fig. 8). Terminals on end of wires must be either closed loop or open-end spade lugs with upturned ends. Cord must have strain relief properly installed. See Steps 4a. for 4-Wire or 4b. for 3-Wire connections. 3. ELECTRICAL CONNECTION TO RANGE. The Rear Access Cover must be removed (Fig 9). To remove, loosen center screw (one screw) and remove cover. The terminal block will then be accessible. 3 & 4 - Wire electrical wall Receptacle types & remodeled installations O Requi4reWdirfoerWnaellw and Receptacle (14-50R) O Fig. 8 exisiting installations A3llWowireedWfoarll Receptacle (10-5OR) NOTE: Range is shipped from factory with 1-3/8" dia. hole as shown. To use either 7/8" dia. hole or 1-1/8" dia. knockouts refer to Fig. 9. 1-1/8" Dia. Knockout (See Chart) Mounting Plate 7/8" Dia. Hole (See Chart) _:_r Access Cover 1-3/8" Hole (See Chart) Fig. 9 Pocket for Cable Mounting Plate Range Connection Opening Size Chart Supply Cord Kit ampere rating information. See serial plate on range for kilowatt rating data, See Serial Plate on Range for KW Rating 120/240 VoIts 120/208 VoIts Cord Kit Ampere Rating Diameter (inches) of Range connection Opening Cord Kit Permanent Wiring 8.8-16.5 KW 7,9-12,5 KW 16.6-22.5 KW !2.6-18.5 KW 40/50 Amp 50Amp 1_3/8 in. 1-3/8 in, 1-1/8 in, 1-3/8 in. Fig. 10 f .... Strain Separate Strain Relief before installation Fig. 11 4A. POWER CORD CONNECTIONS (4-Wire Connection Instructions - Refer to Fig.12) Before wiring the range review the suggested power source location drawing in Fig. 3. If connecting to a 4-Wire electrical system (new branch-circuit or mobile home requires 4-Wire connection): 1. Follow the manufacturer's installation instructions supplied with the strain relief and install (Also see Figs. 9, 10 & 11). 2. Insert the end connectors for Line 1, Line 2 and Neutral and tighten securely to the terminal block. IMPORTANT NOTE: DO NOT LOOSEN the factory installed nut connections which secure the range wiring to the terminal block. Electrical failure or loss of electrical connection may occur if these 3 nuts are loosened or removed. 3. You must disconnect the ground strap. Remove the factory installed ground screw & plate to release the copper ground strap from the frame of the appliance. Cut and discard the copper ground strap & plate. KEEP the ground screw. 4. Connect the ground wire (Green) lead with the eyelet to the frame of the appliance with the ground screw using the same hole in the frame where the ground screw was originally installed (See Fig. 12). 5. Make sure all screws are tightened securely and replace the rear access cover (See Fig. 9). 4-Wire Connection 3 Factory installed connections Connect (DO NOT LOOSEN) neutral Terminal center) here Connect line 1 here Cut ground strap. Discard ground strap & ground plate Connect g= insulated copper ground wire with ground screw here NOTES: restart strain-redef bushing. Center or white wire must always be attached to the center termina_ on brock Connect =ine 2 here Fig. 12