Kenwood DDX6033BT User Manual - Page 77

Accessories/Installation Procedure

Get Kenwood DDX6033BT PDF manuals and user guides View all Kenwood DDX6033BT manuals
Add to My Manuals
Save this manual to your list of manuals

Page 77 highlights

Accessories/Installation Procedure Accessories 1 5 ..........1 ..........6 2 6 *2 ..........1 (2m) ..........1 (3m) 3 *1 7 ..........1 ..........1 4 *1 DDX6033BT/ DDX4033BT/DDX4033 of sale in Australia only. *2 DDX6033BT/ ..........6 DDX6033BTM/ DDX4033BT/ DDX4033BTM only. Installation Procedure 1 To prevent a short circuit, remove the key from the ignition and disconnect the · battery. 2 Make the proper input and output wire connections for each unit. 3 Connect the speaker wires of the wiring harness. 4 Connect the wiring harness wires in the following order: ground, battery, ignition. 5 Connect the wiring harness connector to the unit. 6 Install the unit in your car. 7 Reconnect the · battery. 8 Press the reset button. 9 Perform the Initial Setup. WARNING • If you connect the ignition wire (red) and the battery wire (yellow) to the car chassis (ground), you may cause a short circuit, that in turn may start a fire. Always connect those wires to the power source running through the fuse box. • Do not cut out the fuse from the ignition wire (red) and the battery wire (yellow). The power supply must be connected to the wires via the fuse. ¤ • Mounting and wiring this product requires skills and experience. For best safety, leave the mounting and wiring work to professionals. • Make sure to ground the unit to a negative 12V DC power supply. • Do not install the unit in a spot exposed to direct sunlight or excessive heat or humidity. Also avoid places with too much dust or the possibility of water splashing. • Do not use your own screws. Use only the screws provided. If you use the wrong screws, you could damage the unit. • If the power is not turned ON ("Miswiring DC Offset Error", "Warning DC Offset Error" is displayed), the speaker wire may have a shortcircuit or touched the chassis of the vehicle and the protection function may have been activated. Therefore, the speaker wire should be checked. • If your car's ignition does not have an ACC position, connect the ignition wires to a power source that can be turned on and off with the ignition key. If you connect the ignition wire to a power source with a constant voltage supply, such as with battery wires, the battery may be drained. • Only for DDX6033BT/DDX6033BTM/DDX6033: If the console has a lid, make sure to install the unit so that the faceplate will not hit the lid when closing and opening. • If the fuse blows, first make sure the wires are not touching to cause a short circuit, then replace the old fuse with one with the same rating. English 77

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
English
77
Accessories/Installation Procedure
Accessories
1
..........
1
2
..........
1
(2m)
3
*
1
..........
1
4
..........
6
5
..........
6
6
*
2
..........
1
(3m)
7
..........
1
*
1
DDX6033BT/
DDX4033BT/DDX4033
of sale in Australia
only.
*
2
DDX6033BT/
DDX6033BTM/
DDX4033BT/
DDX4033BTM only.
Installation Procedure
1
To prevent a short circuit, remove the key
from the ignition and disconnect the
·
battery.
2
Make the proper input and output wire
connections for each unit.
3
Connect the speaker wires of the wiring
harness.
4
Connect the wiring harness wires in the
following order: ground, battery, ignition.
5
Connect the wiring harness connector to
the unit.
6
Install the unit in your car.
7
Reconnect the
·
battery.
8
Press the reset button.
9
Perform the Initial Setup.
WARNING
• If you connect the ignition wire (red) and the
battery wire (yellow) to the car chassis (ground),
you may cause a short circuit, that in turn may
start a fire. Always connect those wires to the
power source running through the fuse box.
• Do not cut out the fuse from the ignition wire
(red) and the battery wire (yellow). The power
supply must be connected to the wires via the
fuse.
¤
• Mounting and wiring this product requires
skills and experience. For best safety, leave the
mounting and wiring work to professionals.
• Make sure to ground the unit to a negative 12V
DC power supply.
• Do not install the unit in a spot exposed to direct
sunlight or excessive heat or humidity. Also avoid
places with too much dust or the possibility of
water splashing.
• Do not use your own screws. Use only the screws
provided. If you use the wrong screws, you could
damage the unit.
• If the power is not turned ON (“Miswiring
DC Offset Error”, “Warning DC Offset Error” is
displayed), the speaker wire may have a short-
circuit or touched the chassis of the vehicle and
the protection function may have been activated.
Therefore, the speaker wire should be checked.
• If your car’s ignition does not have an ACC
position, connect the ignition wires to a power
source that can be turned on and off with the
ignition key. If you connect the ignition wire to
a power source with a constant voltage supply,
such as with battery wires, the battery may be
drained.
• Only for DDX6033BT/DDX6033BTM/DDX6033:
If the console has a lid, make sure to install the
unit so that the faceplate will not hit the lid when
closing and opening.
• If the fuse blows, first make sure the wires are not
touching to cause a short circuit, then replace the
old fuse with one with the same rating.