Kenwood KDC-6051U User Manual - Page 42
Audio Preset Memory, X’Over Setting, Display, Range, Operation type, Operation
View all Kenwood KDC-6051U manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 42 highlights
DSP Setup X'Over Setting Fine adjusting the following setting values corresponding to the X'Over values set in the section (page 40). Display Item "X'Over" "Front" "FC" "SLOPE" "Rear" "FC" "SLOPE" "SubWoofer" "FC" "SLOPE" "PHASE" Range Front High Pass Filter Through, 30, 40, 50, 60, 70, 80, 90, 100, 120, 150, 180, 220, 250 (Hz) Front High Pass Slope -6, -12, -18, -24 dB/Oct Rear High Pass Filter Through, 30, 40, 50, 60, 70, 80, 90, 100, 120, 150, 180, 220, 250 (Hz) Rear High Pass Slope -6, -12, -18, -24 dB/Oct Subwoofer Low Pass Filter 30, 40, 50, 60, 70, 80, 90, 100, 120, 150, 180, 220, 250*, Through (Hz) Subwoofer Slope -6, -12, -18, -24 dB/Oct Subwoofer Phase Reverse (180°)/ Normal (0°) ( : Factory setting) 1 Select the source Press the [SRC] button. Turn the [VOL] knob and press it when the desired item is displayed. Select a source other than "STANDBY". ✍✍SRC Select mode 2: Pressing the [SRC] button repeatedly switches source. 2 Enter Audio Control mode Press the [VOL] knob. 3 Enter X'Over setting mode Turn the [VOL] knob and press it when the desired item is displayed. Select "Detailed Setup" > "X'Over". 4 Select the speaker you want to set Turn the [VOL] knob and press it when the desired item is displayed. Select "Front", "Rear", or "SubWoofer". 5 Select the item you want to set Operation type Selects the item. Adjust each item. Set the value Operation Turn the [VOL] knob. Press the [4] or [¢] button. Press the [VOL] button. 6 Repeat steps 3 to 4 to complete the X'Over settings. 7 Exit Audio Control mode 42 | KDC-BT61U/ KDC-6051U Press the [MENU] button for at least 1 second, and then press it again briefly. Audio Preset Memory Registering the value setup by Sound Control. 1 Setup Sound Control Refer to the following operations to setup the Sound Control. - Car Type Selection (page 40) - Speaker Setting (page 40) - Car Type Fine Adjustments (page 41) - X'Over Setting (page 42) - Manual Equalizer Control (page 37) - Listening Position Selection (page 38) - Listening Position Fine Adjustments (page 38) 2 Enter Audio preset memory mode Turn the [VOL] knob and press it when the desired item is displayed. Select "Detailed Setup" > "Preset" > "Memory". 3 Select the number to put in the memory Turn the [VOL] knob and press it when the desired item is displayed. Select a preset number. 4 Turn the [VOL] knob and press it when the desired item is displayed. Select "YES". "Memory Completed" is displayed. 5 Exit Audio Control mode Press the [MENU] button for at least 1 second, and then press it again briefly. ⁄ • Register 6 patterns of Audio Preset Memory. • Preset number "1": When you press the Reset, all the sources will be the setting value which is registered. • Preset number "1" and "2": The memory cannot be erased by the Reset button. • This function cannot be registered when the iPod Equalizer set in (page 37).