Kenwood VR-716 User Manual - Page 18

Operations, Normal playback, Preparing for playback, Listening to a source component

Get Kenwood VR-716 PDF manuals and user guides View all Kenwood VR-716 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

Normal playback Preparing for playback Some preparatory steps are needed before starting playback. SPEAKERS POWER ON/OFF ON/STANDBY Listening to a source component VOLUME CONTROL AUTO INPUT SELECTOR Turning on the receiver 1 Turn on the power to the related components. 2 Turn on the power to this receiver by pressing POWER ON/ STANDBY key. Selecting the input mode If you have selected a component connected to the CD/DVD, VIDEO 2 or DVD/6CH jacks, make sure that the input mode setting is correct for the type of audio signal to be used. 8 Selecting MD/TAPE Select the source name corresponding to the component connected to the MD/TAPE jacks. The initial factory setting is "TAPE". To change the source to "MD", follow the steps below: 1 Use the INPUT SELECTOR knob to select "TAPE". 2 Hold down the AUTO key for more than 2 seconds. • The source indication changes to "MD". • To return to the original indication, repeat procedure 2. Setting the speaker status The speaker indicator lights up. Input Selector INPUT SELECTOR ¢+ + 4 + VOL 1Use the INPUT SELECTOR knob or keys to select the source you want to listen to. The input sources change as shown below: 1 "AUX" 2 "TUNER" 3 "CD/DVD" 4 "TAPE" or "MD" 5 "VIDEO1" 6 "VIDEO2" 7 "DVD/6CH" 2Start playback from the selected source. 3Use the VOLUME CONTROL knob or VOL +/- keys to adjust the volume. Press the SPEAKERS ON/OFF key to switch the speakers on or off. 18 EN

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
18
EN
Listening to a source component
1
Use the INPUT SELECTOR knob or keys to select the source
you want to listen to.
The input sources change as shown below:
1
“AUX”
2
“TUNER”
3
“CD/DVD”
4
“TAPE” or “MD”
5
“VIDEO1”
6
“VIDEO2”
7
“DVD/6CH”
2
Start playback from the selected source.
3
Use the VOLUME CONTROL knob or VOL +/– keys to adjust the
volume.
Normal playback
Some preparatory steps are needed before starting playback.
Turning on the receiver
1
Turn on the power to the related components.
2
Turn on the power to this receiver by pressing POWER ON/
STANDBY
key.
Selecting the input mode
If you have selected a component connected to the
CD/DVD, VIDEO 2
or
DVD/6CH
jacks, make sure that the input mode setting is correct for
the type of audio signal to be used.
8
Selecting MD/TAPE
Select the source name corresponding to the component connected to
the MD/TAPE jacks. The initial factory setting is
“TAPE”
. To change the
source to
“MD”
, follow the steps below:
1
Use the INPUT SELECTOR knob to select “TAPE”.
2
Hold down the AUTO key for more than 2 seconds.
• The source indication changes to
“MD”
.
• To return to the original indication, repeat procedure
2
.
Setting the speaker status
Press the SPEAKERS ON/OFF key to switch the speakers on or off.
Preparing for playback
The speaker indicator lights up.
4
¢
+
+
+
INPUT SELECTOR
VOLUME CONTROL
Input
Selector
VOL
INPUT SELECTOR
POWER
ON/STANDBY
SPEAKERS
ON/OFF
AUTO