KitchenAid KP2671XAC Instruction and Recipe Booklet - Page 9

Assembling Your Bowl Lift Mixer

Get KitchenAid KP2671XAC - Professional Stand Mixer PDF manuals and user guides
UPC - 050946866635
View all KitchenAid KP2671XAC manuals
Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

Assembling Your Bowl Lift Mixer To Attach Bowl 1. Be sure speed control is OFF and stand mixer is unplugged. 2. Place bowl lift handle in down position. 3. Fit bowl supports over locating pins. 4. Press down on back of bowl until bowl pin snaps into spring latch. 5. Raise bowl before mixing. RAISE 6. Plug into a grounded 3 prong outlet. To Raise Bowl 1. Rotate handle to straight-up position. 2. Bowl must always be in raised, locked position when mixing. To Lower Bowl 1. Rotate handle back and down. To Remove Bowl 1. Be sure speed control is OFF and stand mixer is unplugged. 2. Place bowl lift handle in down position 3. Remove flat beater, wire whip, or dough hook. 4. Grasp bowl handle and lift straight up and off locating pins. To Attach Flat Beater, Wire Whip, or Dough Hook 1. Slide speed control to OFF and unplug. 2. Slip flat beater on beater shaft. PIN 3. Turn beater to left, hooking beater over the pin on shaft. 4. Plug into a grounded 3 prong outlet. To Remove Flat Beater, Wire Whip, Or Dough Hook 1. Slide speed control to OFF and unplug. 2. Press beater upward and turn right. 3. Pull beater from beater shaft. Household Stand Mixer Speed Control RESET OFF/0STIR Plug into a grounded 3 prong outlet. Speed control lever should always be set on lowest speed for starting, then gradually moved to desired higher speed to avoid splashing ingredients out of bowl. See the "Speed Control Guide" section. Auto-Reset Motor Protection If the stand mixer stops due to overload, slide the speed control lever to OFF. After a few minutes, the stand mixer will automatically reset. Slide the Speed Control Lever to the desired speed and continue mixing. If the unit does not restart, see the "Troubleshooting Problems" section. 9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
9
Assembling Your Bowl Lift Mixer
To Attach Bowl
1.
Be sure speed control is OFF and
stand mixer is unplugged.
2.
Place bowl lift handle in down
position.
3.
Fit bowl supports over locating
pins.
4.
Press down on back of bowl
until bowl pin snaps into spring
latch.
5.
Raise bowl before mixing.
6.
Plug into a grounded 3 prong
outlet.
To Raise Bowl
1.
Rotate handle to straight-up
position.
2.
Bowl must always be in raised,
locked position when mixing.
To Lower Bowl
1.
Rotate handle back and down.
To Remove Bowl
1.
Be sure speed control is OFF and
stand mixer is unplugged.
2.
Place bowl lift handle in down
position
3.
Remove flat beater, wire whip,
or dough hook.
4.
Grasp bowl handle and lift
straight up and off locating pins.
To Attach Flat Beater, Wire Whip,
or Dough Hook
1.
Slide speed control to OFF and
unplug.
2.
Slip flat beater on beater shaft.
3.
Turn beater to left, hooking
beater over the pin on shaft.
4.
Plug into a grounded 3 prong
outlet.
To Remove Flat Beater, Wire
Whip, Or Dough Hook
1.
Slide speed control to OFF and
unplug.
2.
Press beater upward and turn
right.
3.
Pull beater from beater shaft.
Household Stand Mixer
Speed Control
Plug into a grounded 3 prong
outlet. Speed control lever should
always be set on lowest speed for
starting, then gradually moved to
desired higher speed to avoid
splashing ingredients out of bowl.
See the “Speed Control Guide”
section.
Auto-Reset Motor Protection
If the stand mixer stops due to
overload, slide the speed control
lever to OFF. After a few minutes,
the stand mixer will automatically
reset. Slide the Speed Control Lever
to the desired speed and continue
mixing.
If the unit does not restart, see the
“Troubleshooting Problems”
section.
PIN
OFF/0
STIR
RESET
RAISE