KitchenAid KSM7581MS Use & Care Guide - Page 9

Assembling Your Bowl Lift Stand Mixer

Get KitchenAid KSM7581MS PDF manuals and user guides View all KitchenAid KSM7581MS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

Assembling Your Bowl Lift Stand Mixer To Attach Bowl 1. Turn speed control to OFF. 2. Unplug Stand Mixer or disconnect power. 3. Place bowl lift lever in down position. 4. Fit bowl supports over locating pins. 5. Press down on back of bowl until bowl pin snaps into spring latch. 6. Raise bowl before mixing. 7. Plug into a grounded 3 prong outlet or reconnect power. To Remove Bowl 1. Turn speed control to OFF. 2. Unplug Stand Mixer or disconnect power. 3. Place bowl lift lever in down position 4. Remove flat beater, wire whip, or dough hook. 5. Grasp bowl handle and lift straight up and off locating pins. To Raise Bowl 1. Rotate lever to straight-up position. 2. Bowl must always be in raised, locked position when mixing. To Lower Bowl 1. Rotate lever back and down. To Attach Flat Beater, Wire Whip, or Dough Hook 1. Turn speed control to OFF. 2. Unplug Stand Mixer or disconnect power. 3. Slip flat beater on beater shaft and press upward as far as possible. 4. Turn beater to right, hooking beater over the pin on shaft. 5. Plug into a grounded 3 prong outlet or reconnect power. To Remove Flat Beater, Wire Whip, or Dough Hook 1. Turn speed control to OFF. 2. Unplug Stand Mixer or disconnect power. 3. Press beater upward as far as possible and turn left. 4. Pull beater from beater shaft. 5. Plug into a grounded 3 prong outlet or reconnect power. Commercial Stand Mixer SPEED Control and Lever Guard The Soft Start™ feature minimizes splash-out by starting the mixer slowly before increasing to the selected speed. To further reduce the potential for splash-out, always begin mixing using the STIR speed, then gradually move to higher speeds as needed. See "Speed Control Guide". Auto-Reset Motor Protection If the Stand Mixer stops due to overload, slide the speed control lever to OFF. After a few minutes, the stand mixer will automatically reset. Slide the Speed Control Lever to the desired speed and continue mixing. If the Stand Mixer does not restart, see "Troubleshooting Problems". 9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
9
Assembling Your Bowl Lift Stand Mixer
To Attach Bowl
1. Turn speed control to OFF.
2. Unplug Stand Mixer or disconnect power.
3. Place bowl lift lever in down position.
4. Fit bowl supports over locating pins.
5. Press down on back of bowl until
bowl pin snaps into spring latch.
6. Raise bowl before mixing.
7. Plug into a grounded 3 prong outlet
or reconnect power.
To Remove Bowl
1. Turn speed control to OFF.
2. Unplug Stand Mixer or disconnect
power.
3. Place bowl lift lever in down position
4. Remove flat beater, wire whip, or
dough hook.
5. Grasp bowl handle and lift straight
up and off locating pins.
To Raise Bowl
1. Rotate lever to straight-up position.
2. Bowl must always be in raised, locked
position when mixing.
To Lower Bowl
1. Rotate lever back and down.
To Attach Flat Beater, Wire Whip,
or Dough Hook
1. Turn speed control to OFF.
2. Unplug Stand Mixer or disconnect
power.
3. Slip flat beater
on beater shaft
and press upward
as far as possible.
4. Turn beater to right, hooking beater
over the pin on shaft.
5. Plug into a grounded 3 prong outlet
or reconnect power.
To Remove Flat Beater, Wire Whip,
or Dough Hook
1. Turn speed control to OFF.
2. Unplug Stand Mixer or disconnect
power.
3. Press beater upward as far as
possible and turn left.
4. Pull beater from beater shaft.
5. Plug into a grounded 3 prong outlet
or reconnect power.
Commercial Stand Mixer SPEED
Control and Lever Guard
The Soft Start™ feature minimizes
splash-out by starting the mixer slowly
before increasing to the selected
speed. To further reduce the potential
for splash-out, always begin mixing
using the STIR speed, then gradually
move to higher speeds as needed. See
“Speed Control Guide”.
Auto-Reset Motor Protection
If the Stand Mixer stops due to overload,
slide the speed control lever to OFF.
After a few minutes, the stand mixer
will automatically reset. Slide the Speed
Control Lever to the desired speed
and continue mixing. If the Stand Mixer
does not restart, see “Troubleshooting
Problems”.