Konica Minolta AccurioLabel 190 bizhub PRESS C71cf/AccurioLabel 190 Safety Inf - Page 39

Operation Precautions for the Machine

2

2-32

Accurio Label 190/bizhub PRESS C71cf

2.7

2.7

Operation Precautions for the Machine

To ensure the optimum performance of this machine, observe the precautions described below.

2.7.1

Power Source

The power source requirements are as follows.

Use a power source with as little voltage or frequency fluctuations as possible.

2.7.2

Operating Environment

The environmental requirements for correct operation of the machine are as follows:

-

Operating temperature: 10°C (50°F) to 30°C (86°F)

-

Humidity: 10% to 80%

To prevent the machine trouble, do not install the units in the following places:

-

A place where the ambient temperature drops below 0°C (32°F) or exceeds 40°C (104°F)

-

A place where the relative humidity drops below 30% or exceeds 80%, or where condensation occurs

-

A place subject to dust, salt, metal particles, or oily smoke

-

A place where water, oil, or chemical substances may be splashed

2.7.3

Clothes for Operating the Machine

For the protection of your feet, put on safety shoes (with metallic protectors at the toes).

For the protection of your head, put on a safety hat.

Put on an outer wear with buttons or a zipper and always fasten the buttons or the zipper so that your inner

wears are not caught by the machine. Fasten buttons on wrists of the outer wear or tie off wrists with bands.

2.7.4

Storage of Printed Materials

To store printed materials, follow the recommendation listed below.

-

Printed materials that are to be kept for a long time should be stored where they are not exposed to

light or high temperature in order to prevent them from fading or sticking together.

-

Adhesive that contains solvent (e.g., spray glue) may dissolve the toner on printed materials.

2.7.5

Ozone Release

During print operation, a small quantity of ozone is released. This amount is not large enough to harm anyone

adversely. However, be sure the room where the machine is being used has adequate ventilation, especially

if you are printing a high volume of materials, or if the machine is being used continuously over a long period.

2.7.6

Direct Sunlight

Do not install the machine and its options in a place exposed to direct sunlight, otherwise the machine per-

formance may be degraded or any trouble may be caused.

Destination

North America

Europe, Southeast

Asia, Australia

Voltage

(Single phase for

the main body,

three phases for

the roll winders)

208 V to 240 V AC

220 V to 240 V AC

Frequency

60 Hz

50-60 Hz

Section	Page
Contents	2
1 Introduction	5
1.1 Welcome	5
1.1.1 Configuration and Usage of User’s Guides	5
1.2 Environmental Information	6
1.3 Legal Restrictions on Reproduction	7
2 Safety Information	9
2.1 Warnings and Precautions for Main Body	9
2.1.1 Power Source Connection	10
2.1.2 Installation	11
2.1.3 Using the Product	12
2.1.4 Consumables	13
2.2 Warnings and Precautions for Roll Winder RW-101/Roll Winder RW-201	15
2.2.1 General Information on Safety	15
2.2.2 Warning Classification	15
2.2.3 Classification of Other Indications	16
2.2.4 Safety Precautions	16
2.2.5 Guidelines for Safety Usage (General)	17
2.2.6 Guidelines for Safety Usage (Paper Feeding/Winding)	17
2.2.7 Guidelines for Safety Usage (Safety and Maintenance)	17
2.2.8 Inspections before Power-on	17
2.3 Regulation Notices for Main Body	18
2.3.1 Laser Safety	18
2.3.2 Ozone Release	19
2.3.3 Electromagnetic Interference and Safety Approvals	19
2.3.4 Volatile Organic Compounds (VOC)	20
2.4 Warning and Caution Labels on Main Body	21
2.4.1 Caution Labels on Fusing Part of Fixing Conveyance Unit	21
2.4.2 Warning Label on Waste Toner Box	22
2.4.3 Warning Label for Generation of Volatile Organic Compounds	22
2.4.4 Warning and Caution Labels on Paper Feed Section of Main Body	23
2.4.5 Warning and Caution Labels on Paper Exit Section of Main Body	25
2.5 Warning and Caution Labels on Roll Winder RW-101	26
2.5.1 Warning Labels on the External Front of Roll Winder RW-101	26
2.5.2 Caution Label on the Internal Front of Roll Winder RW-101	30
2.5.3 Caution Label on the Inside of Paper Roll Cover of Roll Winder RW-101	31
2.5.4 Warning Label on the Internal Rear of Roll Winder RW-101	32
2.6 Warning and Caution Labels on Roll Winder RW-201	33
2.6.1 Warning Labels on the Exterior of Roll Winder RW-201	33
2.6.2 Warning and Caution Labels on the Internal Front of Roll Winder RW-201	35
2.6.3 Caution Label on the Inside of Paper Roll Cover of Roll Winder RW-201	37
2.6.4 Warning Label on the Internal Rear of Roll Winder RW-201	38
2.7 Operation Precautions for the Machine	39
2.7.1 Power Source	39
2.7.2 Operating Environment	39
2.7.3 Clothes for Operating the Machine	39
2.7.4 Storage of Printed Materials	39
2.7.5 Ozone Release	39
2.7.6 Direct Sunlight	39

Konica Minolta AccurioLabel 190 bizhub PRESS C71cf/AccurioLabel 190 Safety Inf - Page 39

Operation Precautions for the Machine

Page 39 highlights