Konica Minolta KIP 700 KIP 700 User Manual - Page 22

Treatment against environmental condition, The embedded Dehumidify Heater is an option - print problem

Get Konica Minolta KIP 700 PDF manuals and user guides View all Konica Minolta KIP 700 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

1. 7. 3 Treatment against environmental condition Take a necessary treatment according to the environmental condition as shown below. Humidity(%) Low 40% 70% Possible problem "Void of image", "crease of paper" and other problems occurs when you print with plain paper and tracing paper. "Void of image" occurs when you print with tracing paper. "Void of image" occurs when you print with plain paper and tracing paper. "Void of image", "crease of paper" and other problems occurs when you print with plain paper and tracing paper. Necessary treatment 1. Install an humidifier in the room, and humidify the room air. 2. Remove the paper from the machine right after the completion of print, and keep it in a polyethylene bag. If you will not make print soon, remove the tracing paper from the machine and keep it in a polyethylene bag. Remove the paper from the machine after everyday use, and keep it in a polyethylene bag. If you will not make print soon, remove the tracing paper from the machine and keep it in a polyethylene bag. 1. Use a dehumidifier or such equipment. 2. Remove the paper from the machine right after the completion of print, and keep it in a polyethylene bag. High NOTE (1) The embedded "Dehumidify Heater" is an option. (1) Using a dehumidifier in high humidity environment (65% or higher) is recommended. Refer to [2.10 Dehumidifying Roll Media]. (2) "Void of image" and "crease of paper" will occur in case of extremely high or low humidity. Normal Print Crease of paper If the media is humidified; Normal Print Void of image If the media is humidified; 1-16 Chapter 1 Before Use

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
Chapter 1
Before Use
1-16
1. 7. 3
Treatment against environmental condition
Take a necessary treatment according to the environmental condition as shown below.
Humidity(%)
Possible problem
Necessary treatment
“Void of image”, “crease of paper” and
other problems occurs when you print
with plain paper and tracing paper.
1.
Install an humidifier in the room, and
humidify the room air.
2.
Remove the paper from the machine
right after the completion of print, and
keep it in a polyethylene bag.
“Void of image” occurs when you print
with tracing paper.
If you will not make print soon, remove
the tracing paper from the machine and
keep it in a polyethylene bag.
Remove the paper from the machine after
everyday use, and keep it in a
polyethylene bag.
“Void of image” occurs when you print
with plain paper and tracing paper.
If you will not make print soon, remove
the tracing paper from the machine and
keep it in a polyethylene bag.
Low
40%
70%
High
“Void of image”, “crease of paper” and
other problems occurs when you print
with plain paper and tracing paper.
1.
Use a dehumidifier or such equipment.
2.
Remove the paper from the machine
right after the completion of print, and
keep it in a polyethylene bag.
NOTE
(1) The embedded “Dehumidify Heater” is an option
.
(1)
Using a dehumidifier in high humidity environment (65% or higher) is recommended.
Refer to [2.10
Dehumidifying Roll Media].
(2) “Void of image” and “crease of paper” will occur in case of extremely high or low humidity.
Normal Print
Normal Print
If the media is humidified;
If the media is humidified;
Crease of paper
Void of image