Konica Minolta bizhub PRESS C1070/1070P bizhub PRESS C1070/C1070P/C1060/C71hc/ - Page 62

on the screen., the [back] side of the printed out chart.

Get Konica Minolta bizhub PRESS C1070/1070P PDF manuals and user guides View all Konica Minolta bizhub PRESS C1070/1070P manuals
Add to My Manuals
Save this manual to your list of manuals

Page 62 highlights

5.1 Both Sides Adjustment ( Measure the gap between the front and back sides at each point of [a] to [d] on the [back] side of the printed out chart. - This figure shows an example to measure [a]. >D@ The scale resolution is 0.5 mm. - In this figure, the black line indicates the front EDFN side, and the blue line indicates the back side. - The measurement value can be entered in units of up to 0.1 mm. - For example, as shown in the figure, if the scale of [a] is misaligned 1.5 mm in the plus side compared with the front side, press [1] - [5] - [+/-] to enter "-1.5" as the adjustment value. Then, the blue line on the back side will be moved 1.5 mm toward the minus side. - Write down the measured values so that you do not forget them.  \  [  ) Press [a] to [d] of each point, and enter the adjustment value using the keypad, [,], or [+] on the screen. - If the printing position is misaligned to the minus (-) side, enter a positive value (+). If the printing position is misaligned to the plus (+) side, enter a negative value (-). - To reset a numeric value, press [Clear]. - To switch the positive sign (+) and negative sign (-), press [+/-]. 5-12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
5-12
5.1
Both Sides Adjustment
G
Measure the gap between the front and
back sides at each point of [a] to [d] on
the [back] side of the printed out chart.
-
This figure shows an example to measure [a].
The scale resolution is 0.5 mm.
-
In this figure, the black line indicates the front
side, and the blue line indicates the back
side.
-
The measurement value can be entered in
units of up to 0.1 mm.
-
For example, as shown in the figure, if the
scale of [a] is misaligned 1.5 mm in the plus
side compared with the front side, press [1] -
[5] - [+/-] to enter "-1.5" as the adjustment
value. Then, the blue line on the back side
will be moved 1.5 mm toward the minus side.
-
Write down the measured values so that you
do not forget them.
H
Press [a] to [d] of each point, and enter the adjustment value using the keypad, [
,
], or
[
+
] on the screen.
-
If the printing position is misaligned to the minus (-) side, enter a positive value (+). If the printing
position is misaligned to the plus (+) side, enter a negative value (-).
-
To reset a numeric value, press [Clear].
-
To switch the positive sign (+) and negative sign (-), press [+/-].