Kyocera FS-C5350DN FS-C5350DN Installation Instructions
Kyocera FS-C5350DN Manual
 |
View all Kyocera FS-C5350DN manuals
Add to My Manuals
Save this manual to your list of manuals |
Kyocera FS-C5350DN manual content summary:
- Kyocera FS-C5350DN | FS-C5350DN Installation Instructions - Page 1
use without sufficient clearance may cause overheating. 2 Check the parts and components. CD-ROM Manuals and Other Printed Materials Printer Power Cord Waste Toner Box Toner Containers (4) 2 Installing the Toner Container and Waste Toner Box 1 Open the top cover until it stops. 2 Before - Kyocera FS-C5350DN | FS-C5350DN Installation Instructions - Page 2
printer will begin cleaning the LSU; this will take approximately 70 seconds. 2 Wait until the message display indicates MSG Language. The default . Refer to the Operation Guide to install the printer driver and to set network parameters. © 2009 by KYOCERA MITA Corporation All rights reserved
-
1 -
2
 |
 |
Installation Guide
Clearance
•
Temperature: 10 to 32.5 °C (50 to 90.5 °F)
The humidity should be 70 % or less when the
temperature is 32.5 °C (90.5 °F)
•
Humidity: 15 to 80 %RH
The temperature should be 30 °C (86 °F) or less when the humidity
is 80 %
•
Power Supply: 120 V AC, 60 Hz, 9.2 A / 220 to 240 V AC, 50/60 Hz, 4.7 A
FS-C5350DN
Environment
CAUTION: Be sure to provide enough space around printer. Prolonged use
without sufficient clearance may cause overheating.
400 mm (15-3/4")
250 mm (9-13/16")
200 mm (7-7/8")
600 mm (23-5/8")
Unpacking
CD-ROM
Manuals and Other
Printed Materials
Printer
Power Cord
Toner Containers (4)
Waste Toner Box
Installing the Toner Container and Waste Toner Box
Open the top cover until it stops.
Before installing the toner container, open the slide lever (yellow-colored) on the
developer unit.
The toner container cannot be installed until the slide lever is open.
Proceed as follows:
To open the slide lever, squeeze and hold the lever (1), and slide the lever all the way
toward the direction of the arrow indicated (2) on the lever. When the slide lever is
open, install the toner container.
Push down on the container until it
clicks firmly into place.
Follow the procedure above to install
the other color toner containers.
Note:
Ensure the toner container is in the
correct location for that color.
Close the top cover.
2
1
1
2
5
6
4
Place the new toner container in the
printer with the markings facing
upward.
400 mm
(15-3/4")
Open the cap of the waste toner box.
8
7
Open the left cover.
Unpack the printer and all its included components.
Important:
The printer must be carried by two persons.
Check the parts and components.
1
2
Magenta (M)
Cyan (C)
Yellow (Y)
Black (K)
Cap
Toner Supply Opening
Position the bottom of the waste toner
box in the receptacle and push the box
down until it snaps firmly into place.
9
Hold the toner container with the
upside down markings (caution notes,
etc.) facing downward and shake it 5 or
6 times as shown.
3
Close the left cover.
10
(1)
(2)
FS-C5300DN_IG_EN.fm
1 ページ
２００９年５月１５日
金曜日
午後５時２５分