Kyocera KM-C1530 Fiery X3e Color Guide for Ver 2.0 - Page 55

Using AutoCal and ColorCal, Calibrating with ColorWisePro Tools and AutoCal or ColorCal - kodak

Get Kyocera KM-C1530 PDF manuals and user guides View all Kyocera KM-C1530 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 55 highlights

22-21 Using AutoCal and ColorCal Using AutoCal and ColorCal AutoCal and ColorCal allow you to calibrate the Fiery X3e without the use of an additional spectrophotometer or densitometer. Instead, these methods use the copier's built-in scanner to measure toner density values. Using either AutoCal or ColorCal provides an equally accurate calibration of the Fiery X3e. You can perform AutoCal or ColorCal calibration from either ColorWise Pro Tools or the Fiery X3e Control Panel. For troubleshooting during the AutoCal procedure, see the Job Management Guide. NOTE: To calibrate using AutoCal or ColorCal, you will need the Kodak Gray Scale strip included in the customer media pack that came with your Fiery X3e. You also need the Kodak Gray Scale strip and Kodak Color Control Patches strip to calibrate the scanner of the copier for ColorCal. Calibrating with ColorWise Pro Tools and AutoCal or ColorCal When you run ColorCal from ColorWise Pro Tools, you have the option to calibrate the copier's scanner before calibrating the Fiery X3e itself. This option is not available for AutoCal. It is recommended to calibrate the scanner for ColorCal when the copier output has been adjusted, such as after maintenance or service. TO CALIBRATE WITH COLORWISE PRO TOOLS AND AUTOCAL OR COLORCAL 1. Start Calibrator. For instructions on starting Calibrator, see page 2-6. 2. In the Select Measurement Method pane, choose AutoCal or ColorCal. 3. In the Check Print Settings pane, choose the desired calibration set. If more than one option appears, choose the appropriate calibration set for the type of media you will use most often. NOTE: For this calibration to take effect, the calibration set must be associated with one or more output profiles. The default calibration set is already associated with the default output profile, so there is no need to make any new associations.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
2
2-21
Using AutoCal and ColorCal
Using AutoCal and ColorCal
AutoCal and ColorCal allow you to calibrate the Fiery X3e without the use of an
additional spectrophotometer or densitometer. Instead, these methods use the copier’s
built-in scanner to measure toner density values. Using either AutoCal or ColorCal
provides an equally accurate calibration of the Fiery X3e.
You can perform AutoCal or ColorCal calibration from either ColorWise Pro Tools or
the Fiery X3e Control Panel. For troubleshooting during the AutoCal procedure, see
the
Job Management Guide
.
N
OTE
:
To calibrate using AutoCal or ColorCal, you will need the Kodak Gray Scale
strip included in the customer media pack that came with your Fiery X3e. You also
need the Kodak Gray Scale strip and Kodak Color Control Patches strip to calibrate
the scanner of the copier for ColorCal.
Calibrating with ColorWise Pro Tools and AutoCal or ColorCal
When you run ColorCal from ColorWise Pro Tools, you have the option to calibrate
the copier’s scanner before calibrating the Fiery X3e itself. This option is not available
for AutoCal. It is recommended to calibrate the scanner for ColorCal when the copier
output has been adjusted, such as after maintenance or service.
T
O
CALIBRATE
WITH
C
OLOR
W
ISE
P
RO
T
OOLS
AND
A
UTO
C
AL
OR
C
OLOR
C
AL
1.
Start Calibrator.
For instructions on starting Calibrator, see
page 2-6
.
2.
In the Select Measurement Method pane, choose AutoCal or ColorCal.
3.
In the Check Print Settings pane, choose the desired calibration set.
If more than one option appears, choose the appropriate calibration set for the type of
media you will use most often.
N
OTE
:
For this calibration to take effect, the calibration set must be associated with one
or more output profiles. The default calibration set is already associated with the
default output profile, so there is no need to make any new associations.