LG BGE-103A Owners Manual - Page 13

Procedure

Get LG BGE-103A PDF manuals and user guides View all LG BGE-103A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

PROCEDURE A 1 If you are using the new sleeve (optionally supplied with your unit),skip to step 3. Otherwise, install the plastic grille from the kit. Cut the plastic grille to 25-1/2" wide and 151/4" high. Place the plastic grille to the inside of the wall sleeve at the rear flange. Installation 4 Install the new unit into the wall sleeve. 5 To assemble trim, snap the tab of each piece into the slot of the other piece as shown below. Slide trim over the front of the air conditioner until trim is flush with sleeve as shown below. ENGLISH FIG. 4 2 Fasten the 4 washer screws to secure the grille to the wall sleeve. If you need plastic nuts to mount plastic grille to the inside of the wall sleeve, there are plastic nuts in the installation kit. The nuts are installed from the inside of the sleeve and are pressed into the square holes of the rear flanges. Trim (2 ea) Wall ESnCeaorvgoeyrl Fan Heat MODE Timer TIMER FF12 LHOIGWH TEMP SPFAENED 'F POWER or FIG. 5 3 Remove the backing from the Horizontal Insulation strip 13/8 x 3/8 x 273/16 and attach that to the inside bottom of the sleeve as shown below. Remove the backing from the Around Insulation strip 13/8 x 3/4 x 611/2 and attach that to the inside front of the sleeve as shown below. Around Insulation Horizontal Insulation FIG. 7 • Air conditioners covered in this manual pose an excessive weight hazard. Two or more people are needed to move and install the unit. To prevent injury or strain, use proper lifting and carrying techniques when moving unit. • When handling the air conditioner, be careful to avoid cuts from sharp metal fins on front and rear coils. • Make sure air conditioner does not fall during removal. FIG. 6 Owner's Manual 13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
Owner’s Manual
13
ENGLISH
Installation
PROCEDURE A
If you are using the new sleeve (optionally
supplied with your unit),skip to step 3.
Otherwise, install the plastic grille from the kit.
Cut the plastic grille to 25-1/2" wide and 15-
1/4" high. Place the plastic grille to the inside
of the wall sleeve at the rear flange.
Fasten the 4 washer screws to secure the
grille to the wall sleeve. If you need plastic nuts
to mount plastic grille to the inside of the wall
sleeve, there are plastic nuts in the installation
kit. The nuts are installed from the inside of the
sleeve and are pressed into the square holes
of the rear flanges.
Remove the backing from the Horizontal
Insulation strip 1
3
/8
x
3
/8
x 27
3
/16
and attach that
to the inside bottom of the sleeve as shown
below. Remove the backing from the Around
Insulation strip 1
3
/8
x
3
/4
x 61
1
/2
and attach that
to the inside front of the sleeve as shown
below.
Install the new unit into the wall sleeve.
To assemble trim, snap the tab of each piece
into the slot of the other piece as shown below.
Slide trim over the front of the air conditioner
until trim is flush with sleeve as shown below.
FIG. 4
Around Insulation
Horizontal Insulation
FIG. 6
or
FIG. 5
1
2
3
4
5
Wall
Trim (2 ea)
FIG.
7
•
Air conditioners covered in this manual pose
an excessive weight hazard.Two or more
people are needed to move and install the
unit.
To prevent injury or strain, use proper lifting
and carrying techniques when moving unit.
•
When handling the air conditioner, be careful
to avoid cuts from sharp metal fins on front
and rear coils.
•
Make sure air conditioner does not fall during
removal.