LG DLEX9000V Owners Manual - English Spanish - Page 20

Installing the Side Vent Kit

Get LG DLEX9000V PDF manuals and user guides View all LG DLEX9000V manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

20 INSTALLATION Installing the Side Vent Kit WWARNING t6TFBIFBWZNFUBMWFOU t%POPUVTFQMBTUJDPSUIJOGPJMEVDU t$MFBOPMEEVDUTCFGPSFJOTUBMMJOHUIJTESZFS t5PSFEVDFUIFSJTLPGJOKVSZUPQFSTPOT BEIFSFUPBMM JOEVTUSZSFDPNNFOEFETBGFUZQSPDFEVSFTJODMVEJOH UIFVTFPGMPOHTMFFWFEHMPWFTBOETBGFUZHMBTTFT t'BJMVSFUPGPMMPXBMMPGUIFTBGFUZXBSOJOHTJOUIJT manual could result in property damage, injury to persons, or death. Your new dryer is shipped to vent to the rear. It can also be configured to vent to the bottom or side (right-side venting is not available on gas models). An adapter kit, part number may be purchased from an LG retailer. This kit contains the necessary duct components to change the dryer vent location. 3. Preassemble a 4-inch (10.2 cm) elbow to the next 4-inch (10.2 cm) duct section, and secure all joints XJUIEVDUUBQF#FTVSFUIBUUIFNBMFFOEPGUIFFMCPX faces AWAY from the dryer. Insert the elbow/duct assembly through the side opening and press it onto the adapter duct. Secure it in place with duct tape. #FTVSFUIBUUIFNBMFFOEPGUIFEVDUQSPUSVEFT› inches (3.8 cm) to connect the remaining ductwork. Attach the cover plate to the back of the dryer with the included screw. Cover Plate Elbow 12/4" (3.8 cm) 1. Remove the rear exhaust duct retaining screw. Pull out the exhaust duct. Retaining Screw OPTION 2: BOTTOM VENTING 2. Press the adapter duct onto the blower housing and secure it to the base of the dryer as shown. Adapter Duct Rear Exhaust Duct #SBDLFU OPTION 1: SIDE VENTING 2. Press the tabs on the knockout and carefully remove the knockout for the desired vent opening (rightside venting is not available on gas models). Press the adapter duct onto the blower housing and secure to the base of the dryer as shown. Adapter Duct 3. Insert the 4-inch (10.2 cm) elbow through the rear PQFOJOHBOEQSFTTJUPOUPUIFBEBQUFSEVDU#FTVSF that the male end of the elbow faces down through the hole in the bottom of the dryer. Secure it in place with duct tape. Attach the cover plate to the back of the dryer with the included screw. #SBDLFU ,OPDLPVU Cover Plate Elbow

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
20
Installing the Side Vent Kit
WARNING
manual could result in property damage, injury to
persons, or death.
Your new dryer is shipped to vent to the rear.
It can also be configured to vent to the bottom or side
(right-side venting is not available on gas models).
An adapter kit, part number
, may be
purchased from an LG retailer. This kit contains the
necessary duct components to change the dryer vent
location.
1.
Remove the rear exhaust duct retaining screw. Pull
out the exhaust duct.
OPTION 1: SIDE VENTING
2.
Press the tabs on the knockout and carefully remove
the knockout for the desired vent opening (right-
side venting is not available on gas models). Press the
adapter duct onto the blower housing and secure to
the base of the dryer as shown.
3.
Preassemble a 4-inch (10.2 cm) elbow to the next
4-inch (10.2 cm) duct section, and secure all joints
faces AWAY from the dryer. Insert the elbow/duct
assembly through the side opening and press it onto
the adapter duct. Secure it in place with duct tape.
inches (3.8 cm) to connect the remaining ductwork.
Attach the cover plate to the back of the dryer with
the included screw.
OPTION 2: BOTTOM VENTING
2.
Press the adapter duct onto the blower housing and
secure it to the base of the dryer as shown.
3.
Insert the 4-inch (10.2 cm) elbow through the rear
that the male end of the elbow faces down through
the hole in the bottom of the dryer. Secure it in place
with duct tape.
Attach the cover plate to the back of the dryer with
the included screw.
Rear
Exhaust Duct
Retaining
Screw
Elbow
Cover
Plate
Adapter
Duct
Adapter
Duct
Elbow
Cover
Plate
1
2/4
”
(3.8 cm)
INSTALLATION