LG DLEX9000V Owners Manual - English Spanish - Page 30

fire or death.

Get LG DLEX9000V PDF manuals and user guides View all LG DLEX9000V manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

30 INSTALLATION Connecting Electric Dryers (cont.) USA only WWARNING t$POOFDUUIFQPXFSDPSEUPUIFUFSNJOBMCMPDL $POOFDUFBDIQPXFSDPSEXJSFUPUIFUFSNJOBMCMPDL TDSFXUIBUIBTUIFTBNFDPMPSFEXJSF'PSFYBNQMF  DPOOFDUUIFCMBDLQPXFSDPSEXJSFUPUIFUFSNJOBM CMPDLTDSFXXJUIUIFCMBDLXJSF'BJMVSFUPGPMMPX UIFTFJOTUSVDUJPOTNBZSFTVMUJOBTIPSU PWFSMPBE  fire or death. t(SPVOEJOHUISPVHIUIFOFVUSBMDPOEVDUPSJT QSPIJCJUFEGPS  OFXCSBODIDJSDVJUJOTUBMMBUJPOT   NPCJMFIPNFT   SFDSFBUJPOBMWFIJDMFT BOE  BSFBTXIFSFMPDBMDPEFTQSPIJCJUHSPVOEJOH UISPVHIUIFOFVUSBMDPOEVDUPS Three-wire connection for electric dryers: Direct wire t"XJSFDPOOFDUJPOJT/05QFSNJUUFEPOOFX construction after January 1, 1996. t"6-MJTUFETUSBJOSFMJFGJTSFRVJSFE 1. Remove 31⁄2 inches (8.9 cm) of the outer covering from the wire. Strip 1 inch (2.5 cm) insulation from each XJSF#FOEUIFFOETPGUIFUISFFXJSFTJOUPBIPPL shape. 1" (2.5 cm) t6TF6-MJTUFEXJSF"8(NJOJNVNDPQQFS conductor cable. t"MMPXBUMFBTUGU N MFOHUIUPBMMPXGPSSFNPWBM and reinstallation of the dryer. 3. Attach the two hot leads of the power cord to the outer terminal block screws. Attach the neutral wire to the center terminal block screw. Connect the external ground (if required by local codes) to the green ground screw. 5*()5&/"--4$3&844&$63&-:. Reinstall the terminal block access cover. Ground Screw Hot  #MBDL Neutral (White) Hot (Red) White Wire from Dryer harness External Ground Wire (If required by local codes) 2. Remove the terminal block access cover on the upper back of the dryer. Install a UL-listed strain relief into the power cord through-hole; then thread the power cable prepared in Step 1 through the strain relief. Terminal #MPDL UL-Listed Strain Relief UL-Listed 3-Wire Power Cord

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
30
Connecting Electric Dryers (cont.)
USA only
WARNING
fire or death.
Three-wire connection for electric dryers: Direct wire
construction after January 1, 1996.
1.
Remove 3
1
⁄² inches (8.9 cm) of the outer covering from
the wire. Strip 1 inch (2.5 cm) insulation from each
shape.
2.
Remove the terminal block access cover on the upper
back of the dryer. Install a UL-listed strain relief into
the power cord through-hole; then thread the power
cable prepared in Step 1 through the strain relief.
conductor cable.
and reinstallation of the dryer.
3.
Attach the two hot leads of the power cord to the
outer terminal block screws. Attach the neutral wire to
the center terminal block screw. Connect the external
ground (if required by local codes) to the green
ground screw.
.
Reinstall the terminal block access cover.
1" (2.5 cm)
UL-Listed
Strain Relief
UL-Listed 3-Wire
Power Cord
Terminal
Ground
Screw
Neutral
(White)
Hot
Hot
(Red)
External Ground
Wire (If required
by local codes)
White Wire
from Dryer
harness
INSTALLATION