LG LSC27950ST User Guide - Page 7

Mount the freezer and refrigerator, compartment doors, Water supply installation - door removal

Get LG LSC27950ST PDF manuals and user guides View all LG LSC27950ST manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

Installation Pass the refrigerator Pass the refrigerator laterally through the access door as shown in the right figure. Max 5 4 3 2 1 Min 1 2 TFERMZP TREEMFP 3 4 5 Max Mount the freezer and refrigerator compartment doors Mount them in the reverse sequence of removal after they pass through the access door. Water supply installation Before installation Automatic icemaker operation needs water pressure of 21~121 psi (1.5~8.5 kgf/cm2) (That is, an instant paper cup (6 oz. or 180 cc) will be fully filled within 3 seconds.) If water pressure does not reach the rating 21 psi (1.5 kgf/cm2) or below, it is necessary to purchase a separate pressure pump for normal automatic icing and cool water feed. Keep the total length of the feed water pipe tube within 26' (8 m). Be careful for the tube to avoid being kinked. If the tube is 26' (8 m) or longer it may cause trouble in water feed owing to the drain water pressure. Install the water supply line where it will not be affected by heat. Warning Connect to potable water supply only. Disposal of the old appliance This appliance contains fluids (refrigerant and lubricant) and is made of parts and materials which are reusable and/or recyclable. All the important materials should be sent to the collection center of waste material and can be reused after rework (recycling). For recycling, please contact the local agency. 7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
7
Installation
Mount the freezer and refrigerator
compartment doors
Water supply installation
Pass the refrigerator laterally through the access
door as shown in the right figure.
±
Automatic icemaker operation needs water pressure of 21~121 psi (1.5~8.5
kgf/cm
2
) (That is, an instant paper cup (6 oz. or 180 cc) will be fully filled within
3 seconds.)
±
If water pressure does not reach the rating 21 psi (1.5 kgf/cm
2
) or below, it is
necessary to purchase a separate pressure pump for normal automatic icing and
cool water feed.
±
Keep the total length of the feed water pipe tube within 26’ (8 m). Be careful for the
tube to avoid being kinked. If the tube is 26’ (8 m) or longer it may cause trouble in
water feed owing to the drain water pressure.
±
Install the water supply line where it will not be affected by heat.
±
Connect to potable water supply only.
Mount them in the reverse sequence of removal after they pass through the access
door.
Pass the
refrigerator
Before
installation
Warning
This appliance contains fluids (refrigerant and lubricant) and is made of parts and
materials which are reusable and/or recyclable.
All the important materials should be sent to the collection center of waste material
and can be reused after rework (recycling). For recycling, please contact the local
agency.
Disposal of the
old appliance