Lantronix M110 Series Command Reference - Page 16

At#usbatcom, At#pass

Get Lantronix M110 Series PDF manuals and user guides View all Lantronix M110 Series manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

Chapter 3. Administration Commands info : AT#MATSCR=? #MATSCR: (180) OK 3.7 AT#USBATCOM Enables/Disables cellular AT command over USB. ALLOWED: exec-state-info Note: When turning on, sometimes it depends on behaviour of the device driver on the computer whether the port can be found. If not found, user needs to detach and re-attach the USB port AT#USBATCOM=(flag) - flag: 0 to disable cellular AT commands on the USB port (and allow cellular AT commands on the serial port); 1 to reverse the ports exec : AT#USBATCOM=1 OK state : AT#USBATCOM? #USBATCOM: 1 OK info : AT#USBATCOM=? #USBATCOM: (0-1) OK 3.8 AT#PASS Enables / Disables pass-through mode. ALLOWED: exec-state-info Note: - This command applies to a specific version of software only. - In M113-NB, user can enter either mPACK commands (usually beginning with AT#) or u-Blox com- mands (usually beginning with AT+, or just AT) at one time, but not both. In order to enter the other set of command, the user need to use AT#PASS to switch between the 2 modes: M110 Series Cellular Modem mPACK Command Reference 15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
Chapter 3. Administration Commands
info :
AT#MATSCR=?
#MATSCR: (180)
OK
3.7
AT#USBATCOM
Enables/Disables cellular AT command over USB.
ALLOWED: exec-state-info
Note: When turning on, sometimes it depends on behaviour of the device driver on the computer whether
the port can be found. If not found, user needs to detach and re-attach the USB port
AT#USBATCOM=(flag)
–
flag: 0 to disable cellular AT commands on the USB port (and allow cellular AT commands on the
serial port); 1 to reverse the ports
exec :
AT#USBATCOM=1
OK
state :
AT#USBATCOM?
#USBATCOM: 1
OK
info :
AT#USBATCOM=?
#USBATCOM: (0-1)
OK
3.8
AT#PASS
Enables / Disables pass-through mode.
ALLOWED: exec-state-info
Note:
–
This command applies to a specific version of software only.
–
In M113-NB, user can enter either mPACK commands (usually beginning with AT#) or u-Blox com-
mands (usually beginning with AT+, or just AT) at one time, but not both. In order to enter the other
set of command, the user need to use AT#PASS to switch between the 2 modes:
M110 Series Cellular Modem mPACK Command Reference
15