Lantronix Micro Embedded Integration Kit (EIK) - Integration Guide - Page 9

Connectors, TTL Serial Port, DIL 2 x 6 Pins, CON2 10Base-T, CON3 2 x 2, Pins in place

Get Lantronix Micro PDF manuals and user guides View all Lantronix Micro manuals
Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

CoBox-Micro .200 .400 .200 .068 Figure 2-2 - CoBox-Micro, Connector End View O .115 (Note 1) .465 .170 .065 .087 .060 .400 .625 .150 CONNECTOR END VIEW 1. This is the highest component on the board. .265 .360 .480 Connectors The CoBox-Micro has four connectors: a TTL serial port (CON1), a 10Base-T RJ45 Connector (CON2), and/or pins instead of the RJ45 connector (CON3), and LEDs (CON4). Figure 2-3. CoBox-Micro Connectors 12 CON1 (TTL) 11 CON2 (RJ45) 4 3 2 21 1 87 21 S1 CON3 CON4 (LEDs) The CoBox-Micro that comes with the integration kit is factory configured. When ordering the CoBox-Micro for production use, you can specify each connector as follows: ‹ Pins on/off the board and top/bottom (see Figure 2-2 and Figure 2-3) ‹ LEDs on/off the board ‹ RJ45 on/off the board Contact Lantronix for information about ordering the CoBox-Micro with customized connector configurations. The Embedded Integration Kit (part number Micro-Kit) includes the CoBox-Micro embedded device server. Refer to the following table for a listing of its pinouts. CON1 TTL Serial Port (DIL 2 x 6 Pins) Pin Signal 1 +5VDC Table 2-1. CoBox-Micro Connector Pinouts CON2 10Base-T (RJ45) Connector Pin Signal 1 Tx+ CON3 (2 x 2 Pins in place of RJ45) Pin Signal 1 Tx+ CON4 (2 x 4 Pins in place of LEDs) Pin Signal 1 +5VDC 2-2 Embedded Integration Kit Integration Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
CoBox-Micro
2-2
Embedded Integration Kit Integration Guide
Figure 2-2 - CoBox-Micro, Connector End View
.200
.400
.115
O
.170
.150
.400
.065
.625
.087
.465
.200
.068
.480
.360
.265
.060
CONNECTOR END VIEW
(Note 1)
1. This is the highest component on the board.
Connectors
The CoBox-Micro has four connectors: a TTL serial port (CON1), a 10Base-T RJ45
Connector (CON2), and/or pins instead of the RJ45 connector (CON3), and LEDs
(CON4).
Figure 2-3. CoBox-Micro Connectors
CON1
(TTL)
1
11
2
12
CON2
(RJ45)
CON3
1
2
3
4
1
2
7
8
S1
CON4
(LEDs)
The CoBox-Micro that comes with the integration kit is factory configured. When
ordering the CoBox-Micro for production use, you can specify each connector as
follows:
Pins on/off the board and top/bottom (see Figure 2-2 and Figure 2-3)
LEDs on/off the board
RJ45 on/off the board
Contact Lantronix for information about ordering the CoBox-Micro with customized
connector configurations.
The Embedded Integration Kit (part number Micro-Kit) includes the CoBox-Micro
embedded device server. Refer to the following table for a listing of its pinouts.
Table 2-1. CoBox-Micro Connector Pinouts
CON1
TTL Serial Port
(DIL 2 x 6 Pins)
CON2 10Base-T
(RJ45)
Connector
CON3 (2 x 2
Pins in place of
RJ45)
CON4 (2 x 4 Pins in
place of LEDs)
Pin
Signal
Pin
Signal
Pin
Signal
Pin
Signal
1
+5VDC
1
Tx+
1
Tx+
1
+5VDC