Lantronix SISGM1040-284-LRT CLI Reference Guide Rev E - Page 207

Related Devices, MRP Sample Setup, MRP Pre-Requisites (General), MRP Sample Setup

Get Lantronix SISGM1040-284-LRT PDF manuals and user guides View all Lantronix SISGM1040-284-LRT manuals
Add to My Manuals
Save this manual to your list of manuals

Page 207 highlights

Lantronix SISGM1040-284-LRT CLI Reference Related Devices MRP is implemented on the SISPM1040-384-LRT-C, SISPM1040-362-LRT, SISPM1040-582-LRT, and SISGM1040284-LRT. MRP Sample Setup The example below shows SISPM1040-384-LRT-C switches (one MRM and five MRCs). Figure: MRP Sample Setup MRP Pre-Requisites (General) The following are required to perform MRP setups. 1. Spanning Tree must be disabled at Configuration > Spanning Tree > CIST Port. 2. Other Ring technologies must be disabled (G.8031 EPS, G.8032 ERPS, Rapid-Ring, Ring-To-Ring, etc.). 3. Multiple MRMs in a single ring is not supported. If there are two MRMs in one ring, then both MRMs are generated by the event MULTIPLE_MANAGERS. The multiple active MRMs cause the ring to an incorrect state. Fix: change all active MRMs except one to the MRC state. 4. Other pre-requisites may apply to the specific examples below. 33810 Rev. E https://www.lantronix.com/ Page 207 of 210

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
Lantronix
SISGM1040-284-LRT CLI Reference
33810 Rev. E
Page
207
of
210
Related Devices
MRP is implemented on the SISPM1040-384-LRT-C, SISPM1040-362-LRT, SISPM1040-582-LRT, and SISGM1040-
284-LRT.
MRP Sample Setup
The example below shows SISPM1040-384-LRT-C switches (one MRM and five MRCs).
Figure: MRP Sample Setup
MRP Pre-Requisites (General)
The following are required to perform MRP setups.
1.
Spanning Tree must be disabled at Configuration > Spanning Tree > CIST Port.
2.
Other Ring technologies must be disabled (G.8031 EPS, G.8032 ERPS, Rapid-Ring, Ring-To-Ring, etc.).
3.
Multiple MRMs in a single ring is not supported. If there are two MRMs in one ring, then both MRMs are
generated by the event MULTIPLE_MANAGERS. The multiple active MRMs cause the ring to an incorrect
state. Fix: change all active MRMs except one to the MRC state.
4.
Other pre-requisites may apply to the specific examples below.