Home » Lantronix Manuals » Electronics Accessories » Lantronix WiPort » Manual Viewer

Lantronix WiPort WiPort - User Guide - Page 8

Wireless Bridging, Updating Firmware, Troubleshooting

Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

Table of Contents Monitor Mode Commands 76 8: Wireless Bridging 79 Configuring the WiPort in Bridging Mode 79 Method 1 79 Method 2 79 Method 3 80 9: Updating Firmware 81 Obtaining Firmware 81 Reloading Firmware 81 Using TFTP: Graphical User Interface 81 Using TFTP: Command Line Interface 82 Recovering the Firmware Using the Serial Port 82 10: Troubleshooting 83 Diagnostic LED States 83 Problems and Error Messages 84 Technical Support 86 WiPort User Guide 8

Section	Page
WiPort User Guide	1
Copyright and Trademark	2
Warranty	2
Contacts	2
Disclaimer	3
Revision History	4
Table of Contents	5
1: Using This Guide	9
Purpose and Audience	9
Chapter Summary	9
Additional Documentation	10
2: Introduction	11
Capabilities	11
Applications	12
Protocol Support	12
Configuration Methods	12
Addresses and Port Numbers	13
Hardware Address	13
IP Address	13
Port Numbers	13
3: Using DeviceInstaller	14
Accessing WiPort using DeviceInstaller	14
Viewing the WiPort’s Current Configuration	14
4: Configuration Using Web-Manager	17
Accessing WiPort Web-Manager Using DeviceInstaller	17
Network Configuration	18
Network Mode Configuration	18
Automatic IP Address Configuration	19
Static IP Address Configuration	19
Ethernet Configuration	20
Server Configuration	21
Host List Configuration	23
Channel 1 and Channel 2 Configuration	24
Serial Settings	24
Connection Settings - TCP	26
Connection Settings - UDP	29
Email Configuration	31
Trigger Configuration	32
WLAN Configuration	33
Configurable Pin Settings	36
Apply Settings	38
Apply Defaults	38
5: Configuration via Serial Mode or Telnet Port	39
Accessing Setup Mode	39
Telnet Access	39
Serial Port Access	40
Server Configuration	41
Network Mode	41
Set the IP Address	41
Set the Gateway IP Address	41
Set the Netmask	42
Set DNS Server IP Address	42
Change Telnet Configuration Password	42
DHCP Name	42
Channel 1 and Channel 2 Configuration	43
Baudrate	44
I/F (Interface) Mode	44
Flow	45
Port Number	45
Connect Mode	46
Send the Escape Sequence (+++) in Modem Mode	52
Show IP addr after 'RING'	52
Auto Increment Source Port	53
Remote IP Address	53
Remote Port	53
DisConnMode	53
Flush Mode	54
DisConnTime (Inactivity Timeout)	55
SendChar 1 and SendChar 2	56
Telnet Terminal Type	56
Channel (Port) Password	56
Email Configuration	56
Mail Server	57
Unit Name	57
Domain Name	57
Recipient 1	57
Recipient 2	58
WLAN Settings	59
Topology	60
Network Name (SSID)	60
Adhoc Network Channel	60
Security Suite	60
WEP	60
WPA	61
802.11i/WPA2-PERSONAL	61
Fixed or Automatic Data Rate	62
Transmission Data Rate	62
Minimum TX Data Rate	62
Max TX Failures	63
Enable Power Management	63
Enable Soft AP Roaming	63
Expert Settings	63
TCP Keepalive time in seconds	64
ARP Cache timeout in seconds	64
CPU Performance	64
Disable Monitor Mode	64
HTTP Port Number	64
SMTP Port Number	64
MTU Size	65
TCP Re-transmission Timeout	65
Enable Alternate MAC	65
Ethernet Connection Type	65
Configurable Server Port Number	65
Automatic Host MAC Detection	65
Security Settings	66
Disable SNMP	66
SNMP Community Name	66
Disable Telnet Setup	66
Disable TFTP Firmware Upgrade	66
Disable Port 77FE (Hex)	67
Disable Web Server	67
Disable Web Setup	67
Disable ECHO Ports	67
Enable Encryption	67
Enable Enhanced Password	68
Disable Port 77F0 (Hex)	68
Default Settings	68
Channel 1 Configuration	68
Channel 2 Configuration	68
WLAN Settings	69
Expert Settings	69
Security Settings	70
Email Settings	70
Exit Configuration Mode	70
6: Configurable Pins	71
Default Settings	71
Features	71
Control Protocol	71
Guidelines	71
Commands	72
Examples	74
7: Monitor Mode	76
Entering Monitor Mode via the Serial Port	76
Entering Monitor Mode via the Network Port	76
Monitor Mode Commands	76
8: Wireless Bridging	79
Configuring the WiPort in Bridging Mode	79
Method 1	79
Method 2	79
Method 3	80
9: Updating Firmware	81
Obtaining Firmware	81
Reloading Firmware	81
Using TFTP: Graphical User Interface	81
Using TFTP: Command Line Interface	82
Recovering the Firmware Using the Serial Port	82
10: Troubleshooting	83
Diagnostic LED States	83
Problems and Error Messages	84