Lantronix XPress-DR-IAP APS: Modbus Protocol User Guide - Page 4

Factory Defaults with Reset Pin/Default Pin

Get Lantronix XPress-DR-IAP PDF manuals and user guides View all Lantronix XPress-DR-IAP manuals
Add to My Manuals
Save this manual to your list of manuals

Page 4 highlights

Table of Contents RTS/CTS Mode (1=Fixed 2=Variable 13 Delay after Output of RTS (0-1275 ms, 5ms increments 13 Wait for CTS to Go Active (N/Y 13 Delay after CTS Going Active (0-1275 ms, 5ms increments 14 Delay Dropping RTS after Transmitting (0-1275 ms, 5 ms increments 14 Advanced Modbus Protocol Settings 14 Slave Address (0 for auto, or 1...255 fixed otherwise 14 Allow Modbus Broadcasts (1=Yes 2=No 14 Use MB/TCP 0x0B/0x0A Exception Responses (1=No 2=Yes 14 Disable Modbus/TCP pipeline (1=No 2=Yes 15 Character Timeout (10-7050 msec 15 Message Timeout (200-65000 msec 15 Serial TX delay after RX (0-1275 msec) (0 15 Swap 4x/0x to get 3x//x (1y 16 Unit ID to IP Address Lookup Table 16 Close Idle TCP sockets after (3-60 sec, 0=leave open 17 Redundant Entry Retries after (15-60 sec. 0=disable feature 17 A)dd, D)elete, E)xit Select Function 17 Modbus Address From/To 17 Slave IP Address 17 Security Settings 17 SNMP 18 SNMP community 18 Telnet Setup 18 TFTP Download 18 Port 77FEh 18 Web Server 19 Enable Enhanced Password 19 Port 77F0 (Hex 19 Default Security Settings 19 4: Monitor Mode and Firmware 20 5: WiPort and WiBox Implementation 21 6: XPort Implementation 24 7: xPico Implementation 25 8: Micro125 Implementation 27 9: Factory Defaults with Reset Pin/Default Pin 28 Modbus Protocol User Guide 4

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
Table of Contents
Modbus Protocol User Guide
4
RTS/CTS Mode (1=Fixed 2=Variable) ______________________________________ 13
Delay after Output of RTS (0-1275 ms, 5ms increments)________________________ 13
Wait for CTS to Go Active (N/Y) ___________________________________________ 13
Delay after CTS Going Active (0-1275 ms, 5ms increments) _____________________ 14
Delay Dropping RTS after Transmitting (0-1275 ms, 5 ms increments) _____________ 14
Advanced Modbus Protocol Settings __________________________________________ 14
Slave Address (0 for auto, or 1…255 fixed otherwise) __________________________ 14
Allow Modbus Broadcasts (1=Yes 2=No) ____________________________________ 14
Use MB/TCP 0x0B/0x0A Exception Responses (1=No 2=Yes) ___________________ 14
Disable Modbus/TCP pipeline (1=No 2=Yes) _________________________________ 15
Character Timeout (10-7050 msec) ________________________________________ 15
Message Timeout (200-65000 msec) _______________________________________ 15
Serial TX delay after RX (0-1275 msec) (0) __________________________________ 15
Swap 4x/0x to get 3x//x (1y) ______________________________________________ 16
Unit ID to IP Address Lookup Table ___________________________________________ 16
Close Idle TCP sockets after (3-60 sec, 0=leave open) _________________________ 17
Redundant Entry Retries after (15-60 sec. 0=disable feature) ____________________ 17
A)dd, D)elete, E)xit Select Function ________________________________________ 17
Modbus Address From/To _______________________________________________ 17
Slave IP Address_______________________________________________________ 17
Security Settings __________________________________________________________ 17
SNMP _______________________________________________________________ 18
SNMP community ______________________________________________________ 18
Telnet Setup __________________________________________________________ 18
TFTP Download _______________________________________________________ 18
Port 77FEh ___________________________________________________________ 18
Web Server ___________________________________________________________ 19
Enable Enhanced Password ______________________________________________ 19
Port 77F0 (Hex)________________________________________________________ 19
Default Security Settings ____________________________________________________ 19
4:
Monitor Mode and Firmware
20
5:
WiPort and WiBox Implementation
21
6:
XPort Implementation
24
7:
xPico Implementation
25
8:
Micro125 Implementation
27
9:
Factory Defaults with Reset Pin/Default Pin
28