Home » Lantronix Manuals » Electronics Accessories » Lantronix xPico » Manual Viewer

Lantronix xPico xPico - User Guide - Page 61

Expert Settings Defaults, Setup Mode: Advanced Settings, xPico User Guide

Add to My Manuals
Save this manual to your list of manuals

Page 61 highlights

8: Setup Mode: Advanced Settings Hostlist retry timeout Start character for serial channel 1 (or channel 2) All other parameters 250 (msec) 0x0D (CR) 0 Expert Settings Defaults TCP Keepalive time in s ARP Cache timeout in s CPU Performance Monitor Mode @ bootup HTTP Port Number (1-65535) MTU Size (512 - 1400) TCP Re-transmission timeout (ms) Alternate MAC Ethernet Connection Type 45 600 0 (Regular) Enabled 80 0 (resulting in an operational value of 1400) 500 (msec) Disabled (for OEM use only) 0 (auto-negotiate) Security Settings Defaults Disable SNMP No SNMP community name public Disable Telnet setup No Disable TFTP Firmware Update No Disable Port 77FEh No Disable Web Server No Disable Web Setup No Disable ECHO ports Yes Enable Encryption No Enable Enhanced Password No Disable Port 77F0h No xPico User Guide 61

Section	Page
xPico User Guide	1
Copyright and Trademark	2
Warranty	2
Contacts	2
Disclaimer	3
Revision History	3
Table of Contents	4
List of Tables	8
List of Figures	8
1. Using This Guide	9
Purpose and Audience	9
Chapter Summary	9
Additional Documentation	10
2. Introduction	11
Capabilities	11
Applications	11
Protocol Support	12
Configuration Methods	12
Addresses and Port Numbers	12
Hardware Address	12
IP Address	13
Port Numbers	13
Product Information Label	13
3. Using DeviceInstaller	14
Installing DeviceInstaller	14
Assigning an IP Address	14
Accessing the xPico Using DeviceInstaller	15
Viewing the Current Configuration	15
4. Configuration Using Web Manager	18
Accessing Web-Manager Using DeviceInstaller	18
Network Configuration	19
Network Mode	20
Automatic IP Address Configuration	20
Static IP Address Configuration	21
Ethernet Configuration	21
Server Configuration	22
Server Configuration	23
Advanced	23
Host List Configuration	23
Retry Settings	24
Host Information	24
Channel 1 and 2 Configuration	24
Serial Settings	25
Connection Settings - TCP	27
Connection Settings - UDP	30
Configurable Pin Settings	32
Configurable Pin Functions	32
Apply Settings	33
Apply Defaults	33
5. Configuration via Telnet or Serial Port (Setup Mode)	34
Accessing Setup Mode	34
Telnet Connection	34
Serial Port Connection	35
Exiting Setup Mode	36
6. Setup Mode: Server Configuration	37
Server Configuration (Option 0)	37
IP Address	37
Set Gateway IP Address	38
Netmask: Number of Bits for Host Part	38
Set DNS Server IP Address	38
Change Telnet/Web-Manager Password	38
DHCP Name	39
7. Setup Mode: Channel Configuration	40
Channel 1 (Option 1) or Channel 2 (Option 2)	40
Baudrate	40
I/F (Interface) Mode	41
Flow	41
Port Number	42
Connect Mode	42
a) Incoming Connection	43
b) Response	44
c) Active Startup	44
d) Datagram Type	47
e) Modem Mode	47
Send the Escape Sequence (+++) in Modem Mode	49
Show IP addr after 'RING'	49
Auto Increment Source Port	49
Remote IP Address	50
Remote Port	50
DisConnMode	50
Flush Mode (Buffer Flushing)	51
Pack Control	51
Packing Interval	52
Trailing Characters	52
Send Characters	52
DisConnTime (Inactivity Timeout)	53
Send Characters	53
Telnet Terminal Type	53
Channel (Port) Password	53
8. Setup Mode: Advanced Settings	54
Expert Settings (Option 5)	54
TCP Keepalive time in seconds	54
ARP Cache timeout in seconds	55
CPU Performance	55
Disable Monitor Mode at bootup	55
HTTP Port Number	55
MTU Size	55
TCP Re-Transmission Timeout	56
Enable alternate MAC	56
Ethernet Connection Type	56
Security Settings (Option 6)	56
Disable SNMP	57
SNMP Community Name	57
Disable Telnet Setup	57
Disable TFTP Firmware Upgrade	58
Disable Port 77FE (Hex)	58
Disable Web Server	58
Disable Web Setup	58
Disable ECHO Ports	58
Enable Encryption	59
Enable Enhanced Password	60
Disable Port 77F0 (Hex)	60
Default Settings (Option 7)	60
Channel 1 and Channel 2 Configuration Defaults	60
Expert Settings Defaults	61
Security Settings Defaults	61
9. GPIO Interface	62
Configurable Pins	62
Features	62
Control Protocol	63
Guidelines	63
Commands	63
Examples	65
10. Firmware Upgrades	67
Obtaining Firmware	67
Reloading Firmware	67
Using TFTP: Graphical User Interface	67
Using TFTP: Command Line Interface	68
Recovering the Firmware Using the Serial Port and DeviceInstaller	69
11. Monitor Mode	70
Entering Monitor Mode Using the Serial Port	70
Entering Monitor Mode Using the Network Port	70
Monitor Mode Commands	70
12. Troubleshooting	73
Problems and Error Messages	73
Technical Support	76
A: Binary to Hexadecimal Conversions	77
Converting Binary to Hexadecimal	77
Conversion Table	77
Scientific Calculator	77
B: Compliance	79