Lasko 4305 User Manual - Page 4

MODEL 4305 OPERATION (Figure 5) 1. Plug the cord set into a 120 volt outlet. When the Fan is plugged in, it will "beep" to indicate there is power to the Fan. DO NOT USE EXTENSION CORDS WITH THIS FAN. Extension cords may overheat and cause a fire. Be sure that the plug fits tightly into outlet. When plugs fit loosely into receptacles, they may slip partially or completely out of the receptacle with only the slight movement of the attached cord. Receptacles in this condition may overheat and pose a serious fire hazard; if covered by a curtain,drape, etc. the fire hazard is even greater. 2. Test GFCI (Ground Fault Circuit Interrupter) plug BEFORE EACH USE: 1. Plug GFCI into outlet. Indicator light on the GFCI plug should turn on. 2. Press test button. Indicator light on the GFCI plug should turn off. 3. Press reset button for use. Indicator light on the GFCI plug should turn on. 4. DO NOT USE IF ABOVE TEST FAILS. Power and Speed Control: 1. Turn the Fan ON by pressing the Power/Speed Button ( )) located on the front of the unit. The Fan will start in High Speed. 2. Press the Power/Speed Button ( ) a 2nd time for Medium Speed. 3. Press the Power/Speed Button ( ) a 3rd time for Low Speed. 4. Press the Power/Speed Button ( ) a 4th time to turn the Fan OFF. Internal Oscillation Control: NOTE: This Fan is equipped with an Internal Oscillation Function. The movement occurs INSIDE the Fan housing - the whole Fan WILL NOT move side to side. 1. To turn ON the internal oscillation function, press the Oscillation Button ( ) once. The Oscillation Button will 'blink' to indicate that the Fan is oscillating. 2. To turn OFF the internal oscillation function, press the Oscillation Button ( ) a second time. Control Panel Light: When the Fan is initially plugged in, the Control Panel will be lit. 1. To turn the Control Panel Light OFF, press and HOLD the Power/Speed Button ( ) for 3 seconds. 2. To turn the Control Panel Light ON again, press and HOLD the Power/Speed Button ( ) for 3 seconds. Accent Lighting: This Fan includes a maintenance-free, soft LED accent lighting function for nighttime use. This function can be used while the Fan is ON or OFF. 1. Press and release the Light Button ( ) to turn the Fan Accent Lighting ON to full brightness. 2. Pressing and holding the Light Button ( ) will allow the light level to dim up and down to the desired brightness. 3. Press the Light Button ( ) to turn the Fan Accent Lighting OFF. Control Panel MODEL0 4305 ARMADO (Figuras 1 a 4) NO SE REQUIEREN HERRAMIENTAS 1. Retire el ventilador y sus partes de la caja de cartón. 2. Coloque el ventilador en el lugar deseado al aire libre o en interiores sobre una superficie firme, plana y nivelada. 3. Introduzca manualmente la Varilla de Metal en el orificio ubicado en la parte superior del ventilador. La varilla de metal habrá quedado firmemente asegurada en su lugar cuando usted ya no pueda seguir atornillándola. (Figura 1) Parte Superior del Ventilador Varilla de Metal Figura 1 4. Coloque la Cubierta del Ventilador sobre el ventilador con la flecha ubicada en el lado inferior de la Cubierta del Ventilador apuntando hacia el frente del ventilador donde están ubicados los botones de control. (Figuras 2 y 3) 5. Coloque la Tapa del Ventilador sobre la Varilla de Metal en el centro de la Cubierta del Ventilador. (Figura 4) Cubierta del Ventilador Varilla de Metal Flecha en el Lado Inferior de la Cubierta del Ventilador Figura 2 Apunte la Flecha Hacia el Frente del Ventilador Figura 3 6. Introduzca la Tapa del Ventilador en la Varilla de Metal hasta asegurar completamente. NO AJUSTE EN EXCESO. Tapa del Ventilador Cubierta del Ventilador Varilla de Metal Figure 5 Rev. A 10/07 Light Power/Speed Oscillation 4 Figura 4 2085460 Rev. A 10/07 9 2085460