Lenovo C360 Lenovo C360-365 NT All-In-One Computer Hardware Maintenance Manual - Page 51

Step 16. Lift up the chassis to separate the LED panel from the chassis.

Get Lenovo C360 PDF manuals and user guides View all Lenovo C360 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 51 highlights

Step 3. Disconnect all cables attached to the computer. This includes power cords, input/output (I/O) cables, and any other cables that are connected to the computer. Refer to "Left and right view" and "Rear view" for help with locating the various connectors. Step 4. Remove the stand base. Refer to "Removing the stand base". Step 5. Remove the foot cover. Refer to "Removing the foot cover". Step 6. Remove the memory modules. Refer to "Replacing a memory module". Step 7. Remove the optical drive. Refer to "Replacing the optical drive". Step 8. Remove the stand holder. Refer to "Removing the stand holder". Step 9. Remove the middle cover. Refer to "Removing the middle cover". Step 10. Remove the EMI cover. Refer to "Removing the EMI cover". Step 11. Remove the motherboard. Refer to "Replacing the motherboard". Step 12. Remove the camera. Refer to "Replacing the camera". Step 13. Disconnect the following cables from connectors on the LED panel: • LVDS cable • Converter cable Step 14. Remove the twelve screws that secure the chassis to the front bezel. Step 15. Remove the four screws that secure the LED panel to the chassis. Step 16. Lift up the chassis to separate the LED panel from the chassis. Step 17. To install the new the LED panel: a. Line up the chassis with new LED panel, and then place it into position. b. Secure the LED panel to the chassis with the four screws. c. Connect the converter cable to the new LED panel. d. Line up the chassis and new LED panel with the front bezel, and then place it into position. e. Secure the chassis to the front bezel with the twelve screws. Chapter 7. Replacing hardware 45

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
Step 3. Disconnect all cables attached to the computer. This includes power cords, input/output (I/O)
cables, and any other cables that are connected to the computer. Refer to “Left and right view”
and “Rear view” for help with locating the various connectors.
Step 4. Remove the stand base. Refer to “Removing the stand base”.
Step 5. Remove the foot cover. Refer to “Removing the foot cover”.
Step 6. Remove the memory modules. Refer to “Replacing a memory module”.
Step 7. Remove the optical drive. Refer to “Replacing the optical drive”.
Step 8. Remove the stand holder. Refer to “Removing the stand holder”.
Step 9. Remove the middle cover. Refer to “Removing the middle cover”.
Step 10. Remove the EMI cover. Refer to “Removing the EMI cover”.
Step 11. Remove the motherboard. Refer to “Replacing the motherboard”.
Step 12. Remove the camera. Refer to “Replacing the camera”.
Step 13. Disconnect the following cables from connectors on the LED panel:
• LVDS cable
• Converter cable
Step 14. Remove the twelve screws that secure the chassis to the front bezel.
Step 15. Remove the four screws that secure the LED panel to the chassis.
Step 16. Lift up the chassis to separate the LED panel from the chassis.
Step 17. To install the new the LED panel:
a. Line up the chassis with new LED panel, and then place it into position.
b. Secure the LED panel to the chassis with the four screws.
c. Connect the converter cable to the new LED panel.
d. Line up the chassis and new LED panel with the front bezel, and then place it into position.
e. Secure the chassis to the front bezel with the twelve screws.
Chapter 7
.
Replacing hardware
45