Lenovo IdeaPad S9E Lenovo IdeaPad S9e, S10e and S10 Hardware Maintenance Manua - Page 37

Power, system, checkout, Checking, adapter, operational, charging

Get Lenovo IdeaPad S9E PDF manuals and user guides View all Lenovo IdeaPad S9E manuals
Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

Power system checkout To verify a symptom, do the following: 1. Turn off the computer. 2. Remove the battery pack. 3. Connect the ac adapter. 4. Check that power is supplied when you turn on the computer. 5. Turn off the computer. 6. Disconnect the ac adapter and install the charged battery pack. 7. Check that the battery pack supplies power when you turn on the computer. If you suspect a power problem, see the appropriate one of the following power supply checkouts: v "Checking the ac adapter" v "Checking operational charging" v "Checking the battery pack" on page 30 v "Checking the backup battery" on page 30 Checking the ac adapter You are here because the computer fails only when the ac adapter is used. v If the power-on indicator does not turn on, check the power cord of the ac adapter for correct continuity and installation. v If the computer does not charge during operation, go to "Checking operational charging" To check the ac adapter, do the following: 1. Unplug the ac adapter cable from the computer. 2. Measure the output voltage at the plug of the ac adapter cable. See the following figure: Pin Voltage (V dc) 1 +20 2 2 Ground (20V) 1 3. If the voltage is not correct, replace the ac adapter. 4. If the voltage is acceptable, do the following: v Replace the system board. v If the problem persists, go to "IdeaPad S9e, S10e, and S10" on page 45. Note: Noise from the ac adapter does not always indicate a defect. Checking operational charging To check whether the battery charges properly during operation, use a discharged battery pack or a battery pack that has less than 50% of the total power remaining when installed in the computer. General checkout 29

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
Power
system
checkout
To
verify
a
symptom,
do
the
following:
1.
Turn
off
the
computer.
2.
Remove
the
battery
pack.
3.
Connect
the
ac
adapter.
4.
Check
that
power
is
supplied
when
you
turn
on
the
computer.
5.
Turn
off
the
computer.
6.
Disconnect
the
ac
adapter
and
install
the
charged
battery
pack.
7.
Check
that
the
battery
pack
supplies
power
when
you
turn
on
the
computer.
If
you
suspect
a
power
problem,
see
the
appropriate
one
of
the
following
power
supply
checkouts:
v
“Checking
the
ac
adapter”
v
“Checking
operational
charging”
v
“Checking
the
battery
pack”
on
page
30
v
“Checking
the
backup
battery”
on
page
30
Checking
the
ac
adapter
You
are
here
because
the
computer
fails
only
when
the
ac
adapter
is
used.
v
If
the
power-on
indicator
does
not
turn
on,
check
the
power
cord
of
the
ac
adapter
for
correct
continuity
and
installation.
v
If
the
computer
does
not
charge
during
operation,
go
to
“Checking
operational
charging”
To
check
the
ac
adapter,
do
the
following:
1.
Unplug
the
ac
adapter
cable
from
the
computer.
2.
Measure
the
output
voltage
at
the
plug
of
the
ac
adapter
cable.
See
the
following
figure:
1
(20V)
2
Pin
Voltage
(V
dc)
1
+20
2
Ground
3.
If
the
voltage
is
not
correct,
replace
the
ac
adapter.
4.
If
the
voltage
is
acceptable,
do
the
following:
v
Replace
the
system
board.
v
If
the
problem
persists,
go
to
“IdeaPad
S9e,
S10e,
and
S10”
on
page
45.
Note:
Noise
from
the
ac
adapter
does
not
always
indicate
a
defect.
Checking
operational
charging
To
check
whether
the
battery
charges
properly
during
operation,
use
a
discharged
battery
pack
or
a
battery
pack
that
has
less
than
50%
of
the
total
power
remaining
when
installed
in
the
computer.
General
checkout
29