Lenovo K49 Hardware Maintenance Manual - Page 53

Hard disk drive assembly, Removal steps of memory modules, When installing, Attention

Get Lenovo K49 PDF manuals and user guides View all Lenovo K49 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 53 highlights

Removal steps of memory modules Release the two latches on both edges of the socket at the same time in the direction shown by the arrows 1 , and then unplug the memory module in the direction shown by the arrow 2 . 1 1 2 When installing: Insert the notched end of the memory module into the slot. Press the memory module firmly, and pivot it until it snaps into place. Make sure that it is firmly installed in the slot and does not move easily. Note: If only one memory module is to be installed on the computer you are servicing, the memory module must be installed in SLOT-0 ( a lower slot), but not in SLOT-1 ( b upper slot). b a 1050 Hard disk drive assembly For access, remove these FRUs in order: • "1010 Battery pack" on page 44 • "1020 Bottom slot cover" on page 44 Attention: • Do not drop the drive or apply any physical shock to it. The drive is sensitive to physical shock. Improper handling can cause damage and permanent loss of data. • Before removing the drive, have the user make a backup copy of all the information on it if possible. • Never remove the drive while the computer is operating or is in suspend mode. Chapter 7. Removing and replacing a FRU 47

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
Removal steps of memory modules
Release the two latches on both edges of the socket at the same time in the direction shown by the arrows
1
, and then unplug the memory module in the direction shown by the arrow
2
.
2
1
1
When installing:
Insert the notched end of the memory module into the slot. Press the memory module
firmly, and pivot it until it snaps into place. Make sure that it is firmly installed in the slot and does not
move easily.
Note:
If only one memory module is to be installed on the computer you are servicing, the memory module
must be installed in SLOT-0 (
a
lower slot), but not in SLOT-1 (
b
upper slot).
a
b
1050 Hard disk drive assembly
For access, remove these FRUs in order:
•
“1010 Battery pack” on page 44
•
“1020 Bottom slot cover” on page 44
Attention:
•
Do not drop the drive or apply any physical shock to it. The drive is sensitive to physical shock. Improper
handling can cause damage and permanent loss of data.
•
Before removing the drive, have the user make a backup copy of all the information on it if possible.
•
Never remove the drive while the computer is operating or is in suspend mode.
Chapter 7
.
Removing and replacing a FRU
47